New Washing Equipment Products

Conveyor Parts Washer has modular design.

Model 600 can include rinsing, air-knife blow-off, and drying. System is offered with Allen-Bradley PLC, variety of sensors and fault indicators, and touch-screen interface. Tanks and process chambers are fabricated from 304 stainless steel, allowing flow-through washer to be used with aqueous spray cleaning chemistries without corrosion. Stainless mesh belt, from 16 to 24 in. wide, transports...

Programmable Parts Cleaner washes and dries.

Aqueous Cleaning System has 24 in. wide roller conveyor that carries parts to rotary washer where they rotate at variable speeds on worktable with adjustable, high-pressure spray nozzles at top, sides, and bottom. Parts continue automatically on conveyor to heated dryer, where all moisture is removed. Cyclonic system provides filtration of cleaning fluid and removes particles down to 5 microns.

Cleaning System prepares concrete and steel surfaces.

BlastracÃ-® 2-20D portable blast cleaning system produces 20 in. blast pattern to strip, clean, and profile surfaces in one step. Designed for medium to large sized jobs, its travel speed is rated to 108 ft/minute. System uses two side-by-side blast wheels, positioned to ensure even pattern. It includes twin 15 HP motors, 8-54 dust collector with eight filter cartridges, and automatic pulse...

Pressure Washers are electrically heated.

EH Series stationary, belt-driven presssure washers blast away dirt, oil, and grease from engines, equipment, and concrete. On-demand heat exchanger creates continous hot water. Units include adjustable thermostat, low inlet pressure shutoff, low inlet water volume shutoff, diagnostic control panel, and 50 ft high pressure hose. Trigger gun control offers automatic on/off. Single lance wand has...

A Complete Guide to Aerospace Metal Fabrication eBook

Check out this eBook to learn all about aerospace metal fabrication - materials, processes, and applications.

Pressure Washers are available with Robin engines.

Direct drive Job Pro(TM) cold water pressure washers, suitable for commercial pressure washer applications, are offered with 6.0, 7.0, or 9.0 HP engines. They have low oil protection; 2400, 2700 or 3000 PSI ratings; powder coated steel handles and base plates; and hose wrap with gun/wand holder. Other features include pneumatic tires with tubes, rubber isolators, insulated trigger gun, and 36 in....

Aqueous Washers suit various applications.

VersaForce(i) conveyorized parts washer with immersion cleans with no operator intervention and is suitable for cellular parts manufacturing applications. AquaCell offers in-process cleaning, one person operation, and self-contained design. Recirculating spray wash and air blowoff stages are standard. RTW parts washer has rotating basket below submergence and handles gross amounts of oils and...

Pressure Washers clean with hot water.

HG Series natural gas, stationary hot water pressure washer for wash bays is available in 15 models which have CSA certification to UL1776 specs. Washers have 208, 230, or 460 V, single or three phase motors rated 6.0 or 8.0 hp, with electronic ignition and standing pilot light. Washers also have 24 V control system, vacuum switch, thermal relief valve, overpressure safety controls,...

Pressure Washer provides mobility.

Custom-built, trailer-mounted pressure washer is available as hot or cold, with belt or direct drive, ranging from 5.5 to 37.5 HP in gasoline, electric, or diesel units. Unit features 14 in. tires, surge brakes, 5 x 8 ft wood deck, and tandem axle. Gross vehicle weight is 6,000 lbs, and gross axle weight is 3,500 lbs.

Parts Cleaner includes pneumatic, air-logic system.

L-Series Liftkleens full-immersion devices combine vertical lift agitation and pump-jet cleaning action to ensure effective cleaning of intricate parts, blind holes, and other hard to reach features. Cleaning units, with one-touch control, have emergency stop buttons, anti-tie down devices, and integrated lid and lift platform. Units are capable of hot or cold cleaning with lift platforms up to...

Parts Washer suits lean manufacturing environments.

Portable AquaCell provides in-process cleaning with one-person operation. It supports one-piece operation and small lot flow; has recirculating spray wash and air blowoff stages; and measures 2 x 5 x 8.5 ft. Portable, self-contained design reduces investment and down time.

High or Low Volume Custom Crates and Boxes Available from Reid Packaging

Reid provides mil-spec crates and corrugated boxes in custom dimensions from single to triple wall and will even package them on-site. Check out the video to learn more.