Logic Controller enables automation without programming.
Millenium II+ offers pre-programmed functions and applications to simplify automation control systems for machine manufacturers and panel builders. Application-specific functions include high-speed counting, data-storage function, timing function, and PID function block. Expandable and non-expandable versions are available with 20 I/O. Additional features include temperature sensor, climate...
Read More »
Inverter includes on-board PLC.
Model 3G3MV Inverter with 3G3MV-P10CDT-E PLC eliminates delay of point-to-point wiring. On-board controller features RS-232 and hostlink communication. Direct, dual-port RAM connection gives access to inverter parameters, as well as providing encoder input, interrupt inputs, and digital, pulse, and PWM outputs. Single point programming uses Omron PLC software, and RS-232 serial port enables...
Read More »
Programmable Logic Controller is based on PC architecture.
Type IPC FEC Standard PLC features built-in Ethernet interface and web server technology. Front panel plug-in sensor/actuator wire connector eliminates need for terminal strips. Three-wire version of connector has internally connected bridges for 0 and 24 Vdc. Controller includes 8/16 transistor type digital outputs and 16/32 digital inputs including 2 high-speed units for PNP sensors. FST...
Read More »Vehicle Restraint Controller offers programming software.
Based on Smart-PAK micro ePLC, VRC-G2 incorporates two 15 A relays to control operations of vehicle restraint actuator. Product is programmable using Eware32 ladder logic programming software and offers 24 Timer/Counter registers and 149 internal relays for logic. Controller can be programmed for in 3 configurations: 2 Light, 2 Light with audible alarm, and 3 Light. Offered with 6 board powered...
Read More »Bearing Solutions for Machine Tool Applications
An in-depth overview of the types of bearings used in machine tool applications. Check out this eBook to learn more.
Read More »
Miniature PLCs support all major communications platforms.
Available with Modbus, ABB-CS31, RTU, Profibus DP, Devicenet, CANopen, RCOM, ARCNET, and Ethernet, the 40, 50, and 90 Series Programmable Logic Controllers have 32-bit processors and offer double word memory, PID control, and 32-bit arithmetic. Onboard memory ranges from 34-480 K and is expandable to 2 M with optional flash rom. Devices offer digital I/O to over 1,000 points and analog I/O to...
Read More »Logic Controller offers DeviceNet(TM) Master capability.
With DeviceNet Master Module, GLC2000 series all-in-one HMI and logic controller is compatible with DeviceNet I/O network. Once module is installed, off-line menus can be used to configure slave's MAC address and baud rate. Module supports Polled, Bit-Strobe, Change of State, and Cyclic connection types as well as up to 63 slaves with up to 48 words or bits on each. Series comes with built-in...
Read More »Transceiver-Based FPGAs provide 20 high-speed channels.
Combining 3.125 Gbps transceiver technology with fast FPGA architecture, Stratix(TM) GX EP1SGX40G and Stratix GX EP1SGX40D FPGAs deliver 20 and 8 high-speed transceiver channels, respectively. Former can also deliver 45 channels of embedded dynamic phase alignment (DPA) that support 1 Gbps source-synchronous communication. Based on 0.13 micron process technology, with 1.5 V core voltage, products...
Read More »
Programmable Controllers provide flexible factory control.
Pro-face Series LT Graphic Logic Controllers include Types B+, D, and H. Type B+ provides 32-points of I/O and Flex Network interface. Type D offers DeviceNet master capabilities with HMI. Type H is packed with Discrete I/O, Analog I/O, high-speed counter, and pulse output. Some Type H units have thermocouple or RTD inputs. All LT models include 5.7 in. LCD with HMI features. LT Editor software...
Read More »
Industrial PC provides motion control.
Model CS1000 Automation Control is a modular, DIN-rail-mounted unit that combines MicrosoftÃ-© embedded operating systems and TwinCATÃ-® CE PLC and motion control software in ruggedized hardware platform. It can handle up to 4 PLC tasks and run 1,000 PLC commands in 52 Ã-µsec. It operates up to 5 axes with control cycle time of 2 ms in parallel with PLC program. CX1000 contains 266...
Read More »AS-i Master can be used as PLC or transparent gateway.
Controller-E supports all AS-i 2.1 specifications, provides detailed diagnostics on its backlit LCD display, and offers 1 MB total memory with 128 Kwords devoted to program memory. As gateway, unit can connect up to 868 I/O points on 2 full AS-i systems. Unit acts as 1 node on higher-level bus system. Standard with Profibus interface, product also includes 300+ counters and timers, 5 programming...
Read More »
Solve Any Large-scale Water Control Problem with the Aqua Dam Flood Barrier
Aqua Dam is the ultimate solution for large-scale water control projects. It combines lightweight, large size, and portability all in one innovative product. To learn more about the uses, and applications of Aqua Dam, or to see it in action, check out our new video to get all the details.
Read More »
