Miscellaneous Controls

System allows on-site maintenance of automatic welders.
Miscellaneous Controls

System allows on-site maintenance of automatic welders.

Pro Service System uses indication panel that is housed on rear side of power supply. Control panel is equipped with 4 rows of LED's which indicate state of individual internal supplies, fuses, and components in power supply. Main supply voltage to control panel is also monitored and separate voltage is used to control 1 LED that indicates if board supply is at fault.

Read More »
Limit Controllers utilize optional output cards.
Miscellaneous Controls

Limit Controllers utilize optional output cards.

Plus Series 1/16, 1/8, and Â-¼ DIN Controllers shut down process if parameters exceed preset limits. To prevent safety hazards and equipment damage in oven/furnace, plastics, and packaging industries, they have latching relay that cannot be reset until process is in safe condition. Units offer auto-detection of hardware modules, front panel HMI with dual display, and PC configuration...

Read More »
Integrated Stepper Module controls up to 5 stepper motors.
Miscellaneous Controls

Integrated Stepper Module controls up to 5 stepper motors.

Five Axis Integrated Stepper Module runs on distributed block I/O network, and consumes 3 of 77 available block I/O slots in control system. It includes stepper translator so output is connected directly to stepper motor eliminating need for stepper drive. Five channels of SSI encoder feedback are available for position verification of each stepper motor being controlled. Stepper motion profiles...

Read More »
Motion ICs directly support CANbus interface.
Miscellaneous Controls

Motion ICs directly support CANbus interface.

Available in 1- to 4-axis configurations, Magellan programmable motion processors control dc brush, brushless dc, microstepping, and pulse and direction motors. They provide profile generation, servo loop closure, PLC-style signal manipulation, and motor signal generation. Featuring programmable PID filter with velocity and acceleration feedforward, ICs also offer 32-bit position error, dual...

Read More »
Seal Stuff In, Seal Stuff Out
Sponsored

Seal Stuff In, Seal Stuff Out

One of the best ways to make sure that your machinery stays up and running in the face of adversity is to make sure that it's properly sealed. Of course, it's not always easy to determine whether the integrity of your seals are up to par. How can you tell when you have a problem?

Read More »
Miscellaneous Controls

Motion Control Toolkit works in IEC61131-3 environment.

Motion Control Solution incorporates normative functionalities based on published PLCopen recommendations. Complete set of motion control function blocks supplied by PLCopen is integrated into ISaGRAF toolset ready-to-use. It offers standardization of programming languages and interface toward different motion control solutions allowimg hardware independence and reusability of software...

Read More »
Motion/Logic Control suits 1-3-½ axis systems.
Miscellaneous Controls

Motion/Logic Control suits 1-3-½ axis systems.

By eliminating standalone motion controller and PLC combination, up to 3Â-½ axes can be controlled from SMLC-Lite with Firewire-based motion control networking. ServoWire Controller features Intel Celeron processor, built-in Ethernet, FireWire and serial ports plus adapter, and Flash memory for program storage. All-digital ServoWire SM Drives support variety of actuator technologies,...

Read More »
I/O System offers cabinet-free installation.
Miscellaneous Controls

I/O System offers cabinet-free installation.

Featuring IP65, 66, and 67 protection, Simatic ET 200pro is vibration-proof to 25 g shock load and is installed directly at machine outside control cabinet. Profibus communication and voltage supply can be connected directly using screw-type cable glands at up to 16 A electronic load, M12 or 7/8 in. standard connectors, or Ecofast with prepared cable for data and power. Interface module can be...

Read More »
Miscellaneous Controls

Lightbar Guidance System suits agriculture applications.

AgGPSÂ-® EZ-GuideÂ-® Plus lightbar guidance system is available with choice of steering systems. AgGPS EZ-Steer(TM) provides assisted steering for vehicles with 6-12 in. pass-to-pass accuracy. It uses GPS and electric motor mounted on steering column to keep vehicle on line without use of hydraulics. AgGPS Autopilot(TM) provides fully automated steering capabilities for operations...

Read More »

All Topics