Materials Feeders

Materials Feeders

Wire Feeder uses MaxTrac(TM) heavy-duty wire drive system.

Suited for MIG and metal- or flux-cored wire welding, LF-74 delivers positive arc starting and feeding with stainless steel and aluminum. Its 4-roll MaxTrac(TM) cast aluminum wire drive system delivers consistent feeding force. Accommodating 0.023-1/16 in. MIG wire diameters and .030-5/64 in. flux-cored wire diameters, unit offers feed speeds of 50-800 ipm. Split wire guides provide full support...

Read More »
Automatic Bar Feed offers 4 minute changeovers.
Materials Feeders

Automatic Bar Feed offers 4 minute changeovers.

Using oil-based, hydrostatic support system, Quick Six handles 18 in. to 6 ft long bar stock ranging from 5/16-3 1/8 in. diameter. Menu-driven remote control prompts users through setups, and program data is stored on smart media cards. Standard chain magazine holds 8 pieces of bar stock, and optional side load rack and bar elevator holds up to 50 6-ft bars.

Read More »
Process Controller suits seam welding of thin gauge metals.
Materials Feeders

Process Controller suits seam welding of thin gauge metals.

CSC MIG welding controller utilizes controlled short circuit gas metal arc welding process to clear short circuits by retracting wire from short. Controller syncronizes wire feeder actions with power supply current to continuously feed wire alternatly between forward and reverse directions. Process helps to increase travel speed and eliminate spatter on wide range of materials including steel,...

Read More »
Materials Feeders

Welding System is available in various configurations.

Ready-Pak(TM) kits are available in 4 configurations with various power sources to meet application needs. All kits include LF-72 wire feeder featuring 2-roll MaxTrac(TM) drive system for accurate wire feeding. Other components are power source, drive rolls and wire guide, wire feeder control cable, welding gun, work lead and clamp, and Harris® Flowmeter/Regulator and gas hose. Two kits...

Read More »
Materials Feeders

Dispenser is suited for compound management and logistics.

FlexiWeigh 1000 and 2000 offer capabilities for powder and solvent dispensing, inerting of target containers, and capping/uncapping in addition to labeling, sample tracking, and weighing. Floor-standing, fully enclosed cabinets are equipped with XYZ robot with rotating arm and WISC module, which can combine multiple operations at one vial position. Optimally suited for powders in 1-20 mg range,...

Read More »
Portable Wire Feeder includes Soft Start(TM) run-in control.
Materials Feeders

Portable Wire Feeder includes Soft Start(TM) run-in control.

Voltage-sensing SuitCase(TM) X-TREME(TM) 12VS holds wire spools up to 12 in. and features SunVision(TM) digital meters that display voltage and wire feed speed or amperage, and are visible in direct sunlight. Two drive rolls provide positive feeding with solid wires from .023-5/64 in. and cored wires from .030-5/64 in. Featuring polypropylene case, feeder operates on arc voltages from 14-48 Vdc...

Read More »
Gravimetric Feeder handles plastic pellets and regrind.
Materials Feeders

Gravimetric Feeder handles plastic pellets and regrind.

Consisting of 1-8 feeders and central microprocessor-based controller, ProRate(TM)/Gravimetric Feeder continuously meters raw materials into central station hopper. Each feeder operates in independent, continuous loss-in-weight scaling mode to insure accuracy of each ingredient. Controller monitors weight signals of each feeder and adjusts auger speed to match recipe feed rate. Unit controls 1-8...

Read More »
Bar Feeder handles various sizes and shapes of bar stock.
Materials Feeders

Bar Feeder handles various sizes and shapes of bar stock.

By changing feed tube size, RHINOBAR can be customized for virtually any size bar stock. Tube sizes range from Â-¼-2¾ in. in 1/8 in. increments, accommodating bar stock diameters from 1/8-2¾ in., and up to 12 ft long. Pedestal and barrel clamps provide stability, preventing whip or spin of bar. Oil fills gap between bar stock and feed tube, acting as noise damping support....

Read More »
Bar Feeder utilizes hydrodynamic forces for operation.
Materials Feeders

Bar Feeder utilizes hydrodynamic forces for operation.

Mini-Rhinobar single-tube bar feeder is engineered for Swiss type CNC screw machines and small, fixed-head CNC lathes. Oil fills gap between bar stock and feed tube, acting as noise damping support. Oil flow and pressure are controlled with single valve, which also allows for accurate bar control and minimizes vibration. Mini-Rhinobar can be controlled from remote pendant for safe operation. Feed...

Read More »
Materials Feeders

Volumetric/Weigh Feeder offers simplified functionality.

Able to feed granular and powdered materials, Series 58QP has front cover that removes without tools in order to facilitate inspection and cleaning. Series is also equipped with direct feed auger drive, NTEP weighing system, digital weighing system, and 4.5 x 3.5 in. LCD display capable of tracking up to 12 independent feeder systems. Metering capacity ranges from 20-5,000+ lb/hr, and products...

Read More »
Precision Machining Solutions with Over 25 Years of Experience
Sponsored

Precision Machining Solutions with Over 25 Years of Experience

Quality, customer service, and unbeatable value are the hallmarks of Hogge Precision. Since 1989 we have built a reputation as the go-to precision machining source, servicing many demanding industries. For CNC machining and screw machining, there are few manufacturers that can match our capabilities and expertise. See our video to learn more.

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers