Linear Motors are optimized for speed, positioning.
Used for horizontal or compensated vertical axes, liquid-cooled 1FN3 Peak Load Motors offer Nominal Force (Fn) of 8,100 N, Max Force (Fmax) of 20,700 N, and max velocity of 253 m/min. Liquid-cooled 1FN3 Continuous Load Motors and convection-cooled 1FN6 Magnet Free Secondary are both suited for horizontal, inclined, or compensated vertical axes. Respective values are Fn of 10,375 and 2,110 N, Fmax...
Read More »
Linear Motors promote gas heating efficiency.
Through proportional control of gas flow, Linear Motor Series encourages energy-efficient gas heating control. Modulation of dispensed gas enables fuel to be burned at slower/faster rate as needed, promoting burning efficiency while minimizing expenditure and pollution. Packaged as integrated assembly with motor and valve, series also integrates dual safety system that lets motor switch off valve...
Read More »
Linear Motors feature modulated gas control.
Integrating motor and valve, Linear Motor Series provides proportional control of gas flow for energy-efficient gas heating. Synchronous model provides 10 mm displacement at 115 V, linear step speed of 0.833 or 1.67 mm/sec, and output force of 27-45 N. Featuring dual safety system, 2 stepper-based models incorporate -7.5-
Read More »
Guide To Swageless Fittings
Electroline specializes in innovative, easy-to-install swageless fittings. The following guide will highlight everything you need to know about swageless fittings.
Read More »
Aerotech's New ALS130H Series Direct Drive Positioning Stages Provide Ultra-Low Speed Scanning Solution
September/2008 Aerotech's new ALS130H series linear motor driven positioning stages have been designed for ultra high precision scanning and positioning applications where sub-nanometre level resolution needs to be combined with exceptional smoothness, high traversing speeds and fast acceleration over travel ranges up to 150 mm. The classic two-part stage design outperforms leadscrew driven...
Read More »Motors feature piezoelectric motor driver ASIC.
Piezoelectric motor driver ASIC, NSD-1102 can drive one or two SQL-1.8 SQUIGGLE motors from single 2.8 to 5.5 Vdc supply. It includes on-chip dc-dc step-up converter and 4 half bridge drivers to create pairs of phase-shifted square waves with ultrasonic frequency to drive SQUIGGLE micro motors. Motor and drive circuit draw 100-900 mW when moving, depending on motor speed and load. On-chip...
Read More »
Linear Servo Motors are offered in variety of configurations.
Ranging from 140-6000 N of linear thrust and offered in over 24 coil configurations, Linear Sigma Series PMBL is offered for use with Sigma II digital servo amplifiers. Available in 2 product levels, level-I group provides wide array of linear motors with plug-and-play Sigma II servo amplifiers, while level-II group provides range of fully-integrated linear positioning slides with linear encoders...
Read More »
Linear Synchronous Motors suit large machining centers.
Offering peak forces up to 13,000 N with dead weight of 45 g, IDAM L2U Series compensates for any magnetic forces generated between motors and magnets. By using iron-core linear ac synchronous motor with 2 symmetrically opposed secondary parts, units maintain accuracy and minimize friction-induced heat generation. Reduced iron content in movable primary component further minimizes mass in 3-phase...
Read More »
Closed Loop Digital Interface For Precise AC Or DC Drive System Control
Dart Controls offers the ASP40-420 for applications that require a closed-loop digital interface with a 4-20mA isolated input/output signal and programmable relay outputs. Ideal for use with AC or DC drive systems in chemical metering, mixing, and other process control applications. Custom faceplate artwork is available also. Dart Controls, Inc. is an ISO9001:2000 registered designer,...
Read More »
ALS130H Series Linear Motor Stage
ALS130H Series Linear Motor Stage Provides Outstanding Step-to-Step Resolution for High Precision Alignment o Bi-directional repeatability to 75 nm o Direct-drive linear motor for ultra-precise motion o 23 N (5.2 lb) continuous force linear servomotor o High-accuracy, noncontact, glass-scale linear encoder o Anti-cage creep cross-roller bearings for smooth motion o Outstanding performance in a...
Read More »
Custom Fabrication & Machining Services with Over 30 Years of Experience
As a trusted manufacturer to customers across a broad range of industries, Key Gas Components is a premier provider of CNC machining and tube fabrication. Our entire organization is quality driven and customer-centric, with broad-based manufacturing capabilities that can accommodate the most challenging requirements. See our video to learn more.
Read More »
