Gearheads and Gearboxes

Planetary Gearboxes suit elevator movement applications.
Gearheads and Gearboxes

Planetary Gearboxes suit elevator movement applications.

Constructed for passenger and service elevators, ZF-Ecolift models RME 310 and RME 410 use 2-stage planetary gear design to transmit power to sheave and fulfill elevator technical regulations TRA 200 and TRA 220-229. Suited for motor speeds of 1,000, 1,500, and 3,000 rpm, products may be used with motors up to 50 hp and offer load capacity of up to 5,500 lbs. Units emit low noise due to helical...

Read More »
Planetary Gearboxes mount to all common servomotors.
Gearheads and Gearboxes

Planetary Gearboxes mount to all common servomotors.

ZF-Servoplan PG 2-stage gearboxes offer low backlash of < 2 arc-min for applications requiring exact positioning. They feature large-dimensional taper roller bearings; precision-ground, hardened gears; and Viton seals for IP-65 rating. ZF-Servoplan PGE Gearboxes, for less demanding applications, range from 5-670 Nm with ratios from 3-1000. They include input pilot for proper motor/gearbox...

Read More »
Gearheads and Gearboxes

Planetary Gearheads are offered in 2 new sizes.

Series LP gearheads, suited for general motion control, are now available in 7:1, single-stage and 70:1, 2-stage gear ratios. Series is available in NEMA sizes from 23-56, torque ranges from 46-2,566 lb-in., and ratios from 3:1 through 100:1. LPB series LP gearbox and integrated belt pulley solutions eliminate need for right angle gearbox and couplings. They directly support high belt tensions...

Read More »
Gearbox offers leak-proof, high-speed performance.
Gearheads and Gearboxes

Gearbox offers leak-proof, high-speed performance.

Slide-Rite(TM) Gearbox turns power around any corner, operates in any direction, and slides axially along drive or driven shaft. It allows only 1° of backlash on reversal of input. Solid, one-piece aluminum housing seals gears from outside contaminants and encloses factory-lubricated and sealed bearings and geared shaft. With shaft speeds to 1,200 rpm, product offers 45° helical gears...

Read More »
Variable Speed Drive offers fixed/variable dual setpoints.
Motor Controllers and Drives

Variable Speed Drive offers fixed/variable dual setpoints.

PumpSmart 200 v2.1 requires 7 parameters for set up and start of single pump pressure control applications. Unit also allows users to start up to three fixed speed pumps. Microprocessor based, variable speed drive is programmed for centrifugal pumps up to 700 hp, providing control of process parameters by continuously monitoring and reacting to pump conditions/system demands. Unit alerts user...

Read More »
Reducers feature aluminum construction.
Gearheads and Gearboxes

Reducers feature aluminum construction.

Bravo(TM) Worm Gear Reducers and LeCENTRIC(TM) Inline Reducers feature single piece housings impregnated with Resinol RT, vent-free designs, and factory lubrication with synthetic semi-fluid grease. Bravo model is available in four sizes with ratios from 7:1 to 4,000:1 and output torque up to 4,000 lb-in. LeCENTRIC model is available in four sizes with ratios up to 280:1 and output torque up to...

Read More »
Worm Gear Reducers withstand rigorous washdowns.
Gearheads and Gearboxes

Worm Gear Reducers withstand rigorous washdowns.

All-Stainless reducers are available in 4 center distances in ratios from 5:1 through 100:1 with NEMA C flange, quill or coupling input, reducers feature O-ring on face of input flange and SS output shaft. Gear+Motor(TM) combinations come in single-phase ratings through 1Â-½ hp, three-phase through 5 hp and permanent magnet DC through 1½ hp. Units are suitable for food processing,...

Read More »

All Topics