Prefeeder/Wire Payout works with cutting machines.
Materials Feeders

Prefeeder/Wire Payout works with cutting machines.

Dependent upon material condition, Model APF100 is designed for wire sizes .030-.312 in. and can be used with any Wire and Tubing Cutter or Cut and Strip Machine. Unit prevents material overruns when used with intermittent feed machines. Offering max drive speed of 100 ips, free-standing device accommodates reels up to 18 in. in diameter and 12 in. in width.

Read More »
Plastics Processor uses screwless feeding technique.
Materials Feeders

Plastics Processor uses screwless feeding technique.

Posimax B300 accurately doses free flowing masterbatch or additives into process screw via screw-less feeding mechanism. There are no pockets or screws, and machine incorporates feeding disc as only moving part. Material is fed via rotating disc that creates product lock-up zone, identifying 4 areas where materials pass through. Model B300 feeds materials at rate of 11-1,100 lb/hr.

Read More »
Micro Feeder offers rates as low as 20 g/hr.
Materials Feeders

Micro Feeder offers rates as low as 20 g/hr.

Model MT12, offered in loss-in-weight and volumetric feeder versions, is available for continuous or batch operation. Scale in loss-in-weight models can be installed with optional draft shield. Configured for standard industrial or sanitary applications, feeder design allows feeder bowl to discharge almost completely when emptying. Unit will accurately feed rates from 20-2,000 g/hr, depending on...

Read More »
Tube Loader handles 120 tubes/min.
Parts Feeders

Tube Loader handles 120 tubes/min.

Suited for cosmetics and pharmaceutical filling machines, Universal Feeder handles plastic and metal tubes in all available formats. Machine connects to filler and is divided into 3 zones for storage, separation, and conveying of tubes. It holds up to three 24 x 16 in. boxes at once, providing uninterrupted production time of 11 min for 1 in. dia tubes at speed of 100 tubes/min. Controls enable...

Read More »
CMAA Crane Buyer's Guide
Sponsored

CMAA Crane Buyer's Guide

CMAA has organized this Buyer's Guide to promote standardization and to assist prospective buyer's of electric overhead traveling cranes in selection of equipment most suitable for their applications.

Read More »
Quick Change Feeder is designed for short, customized runs.
Materials Feeders

Quick Change Feeder is designed for short, customized runs.

Quick Change/Quick Clean T35/S60 lets user change from single screw S60 to twin screw T35 configuration as material needs change. It handles feed rates from 0.004-160 ftÂ-³/hr depending on material density. Multi-purpose feeder is available with 2 bowl/screw sets that mount to same gearbox and can be cleaned and swapped out in minutes. Available in volumetric and gravimetric models, product...

Read More »
Materials Feeders

Automatic Bar Feeder has bar capacity of 8-80 mm dia.

Master 880 is compatible with all fixed headstock lathes, and feeds round, square, and hex-shaped bars with minimal noise and no vibration. Precise bar feeding and positioning are controlled by CNC with integrated PLC. Machine can be configured with one of 3 large-capacity magazines that can be located on either side. Bar changeover is 35 sec for 12 ft bars. Patented 2-stage Double Pusher feeding...

Read More »
Materials Feeders

Bar Feeder offers changeovers in under 1 min.

Featuring 2,100 x 1,100 mm footprint, CNC-controlled VIP 80E is suited for running low-to-medium sized production volumes of round, square, and hex bar stock. New bar loads into lathe spindle while last piece is being machined. Rear-mounted 10-30Â-º inclined plane loading rack accommodates sixty 10 mm diameter precut bars, and depending on workpiece, VIP 80E can be operated continuously. Max...

Read More »
Materials Feeders

Automatic Bar Feeders handle 5-65 mm bars at 450 mm/sec.

Model TS 560 Rack comes with 3-4 superimposed moveable rack magazine with capacity of seventy 25 mm diameter bars, while Model TS 560 Bundle magazine offers 2.5 ton capacity. Change time is 25-30 sec for 12 ft bars. Feeders can be connected to automatic and CNC lathes, either fixed or sliding headstock, and with any type of bar-working machine. Guide channels made of wear-resistant spring steel...

Read More »
Materials Feeders

Bar Feeder complements high-speed CNC lathes.

Equipped with 300 mm, sloping plane, multi-bar magazine, TAL 65 feeds bars from 5-65 mm at 250-500 mm/sec. Dual bar support principle uses hydraulic immersion and dynamic support in elastic guide channel to provide high-speed feeding, even when bars are slightly bent. Closed-loop re-circulating oil system feeds oil into elastic guide channels, eliminating bar vibration. Mechanical...

Read More »
Parts Feeders

Spindle Machines include integrated bar loader.

Single-spindle, Models Deco 10a and 13a feature Robobar SBF 216, which reduces channel guide changeover time down to 15 min. With quick-change system, operators index guide block to proper size capacity and changeover is complete. System accommodates up to 150 bars in sizes from 2-16 mm. Gripper system adjusts to whatever bar size is being used in machine. All setups are integrated into machine...

Read More »

All Topics