Vibratory Feeder has 3 mounting options.
Model 68B Heavy-Duty Feeder features suspended 24 x 42 in. tray anchored to below-deck drive with rated capacity of 275 tph (when installed at 10Ã-º slope). Its dust-tight, epoxy-coated, heavy-duty, electromagnetic AC drive ships with N12 solid-state 100% variable speed control unit. Suitable for handling aggregates, slag, coal, ores, or grains, model 68B is available with open and tubular...
Read More »
Wire Feeder has microprocessor control.
DuraDrive4 has 4-roll drive system and grooved-and-driven upper and lower feed rolls to impart maximum feed force to wire. Feed motor handles various torch lengths and wire sizes. Adjustable burnback and run-in start allow operator to select slow start for difficult-to-start wires. Dual-speed switches from low to high-speed without gear or motor changes. Quick-disconnect feed rolls aid in wire...
Read More »
Wire Feeder has microprocessor control.
DuraDrive4 has 4-roll drive system and grooved-and-driven upper and lower feed rolls to impart maximum feed force to wire. Feed motor handles various torch lengths and wire sizes. Adjustable burnback and run-in start allow operator to select slow start for difficult-to-start wires. Dual-speed switches from low to high-speed without gear or motor changes. Quick-disconnect feed rolls aid in wire...
Read More »
Straightener/Feeder features computer control.
LCC-HF2 Straightener/Feeder, equipped with HM-type Computer Control System (CCS), handles metals from 1.97 in. to 39.37 in. wide and up to 0.18 in. thick. It accepts maximum coil weights up to 10 tons and maximum coil O.D.s of 60 in. Features include no-loop detector, photo sensor loop control, pilot roll, handwheel adjustment, end-of-stock detector, and pneumatic or hydraulic expansion systems.
Read More »
Injection Molding from 3D Printed Molds
Check out this white paper to see how 3D printing may be a beneficial alternative to traditional mold making processes.
Read More »
Wire Feeder operates at speeds from 50 to 780 ipm.
Model 714S bench style wire feeder features one tool-less, rotatable drive assembly and automatic run-in. Dual tension control provides independent drive roll pressure on front and back rolls, while trigger hold allows extended welds. 714S runs hard and cored wires from 0.023 to 1/8 in. dia at speeds from 50 to 780 ipm. Spool size capacity is 60 lb, and incorporates Posifeed(TM) four-drive-roll...
Read More »
Wire Feeder operates at speeds from 50 to 780 ipm.
Model 714S bench style wire feeder features one tool-less, rotatable drive assembly and automatic run-in. Dual tension control provides independent drive roll pressure on front and back rolls, while trigger hold allows extended welds. 714S runs hard and cored wires from 0.023 to 1/8 in. dia at speeds from 50 to 780 ipm. Spool size capacity is 60 lb, and incorporates Posifeed(TM) four-drive-roll...
Read More »
Straightener/Feeder features computer control.
LCC-HF2 Straightener/Feeder, equipped with HM-type Computer Control System (CCS), handles metals from 1.97 in. to 39.37 in. wide and up to 0.18 in. thick. It accepts maximum coil weights up to 10 tons and maximum coil O.D.s of 60 in. Features include no-loop detector, photo sensor loop control, pilot roll, handwheel adjustment, end-of-stock detector, and pneumatic or hydraulic expansion systems.
Read More »
SpillVak Absorbs Up to 6X More Fluid Than Rock- and Clay-based Absorbents
Are you struggling to find an absorbent that doesn't result in at least some leaching? SpillVak outperforms all rock and clay-based materials. Check out our video to learn more.
Read More »
