New Converters Products

Synchro To BCD Converters mount on PC boards.

SBC40 series converts synchro or resolver inputs of 11.8 or 90 V at 400 Hz into 3 or 4 decade BCD data representing angle with accuracy of Ã-

TTL and 24V Converters contain two independent channels.

Model 8501 two-channel 5 to 24 V converter requires 7 mA into 382 ohms per channel to provide 7 mA output into the 3 Kohm, 24 V typical PLC logic input. They may be driven by TTL logic, H series TTL logic, or with open collector NPN transistor. Input frequency is DC to 15 KHz. Model 8502 two-channel 24 to 5 V converter requires 7 mA into 2.5 Kohm per channel to provide 5 mA sinking output to TTL...

A/D VME Board handles high frequency applications.

Model 6802 has 32 channels of delta sigma A/D conversion with extremely precise, linear-phase low pass filtering. Each A/D has 24 bits of resolution at sampling rates from 1 kHz to 216 kHz. Front-panel sync input signal allows synchronization of multiple 6802 boards. Outputs of up to eight 6802 boards, for maximum of 256 channels, can be combined over single FPDP cable. Data tagging is also...

Transmitters convert analog input signals to digital data .

DIN-100 Sensor to Computer Modules transmit data via RS-485 to controller, which may be computer or other processor-based equipment. Modules measure temperature, pressure, voltage, current, digital input, or digital output signals. They perform all signal conditioning, scaling, linearization, and conversion to linearized ASCII data values or Modbus RTU data values. Address, baud rate, parity, and...

Direct Acting High Speed Servo Valve (DASV)

Download this paper to learn about how high performance servo valve's can be used in your most demanding hydraulic and pneumatic applications.

Air To Electronic Converter displays air gage signals.

Compact VE-03 mounts as free-standing unit to standard DIN rail. In operation, air input signal is received in front of converter through air adapter. Output signal is transferred to electronic column or gage computer from signal output socket at back of unit. Zero and gain controls on front of converter adjust electric signal. Zero control is used for adjusting zero point on electronic column...

Synchro-Resolver-Encoder Card keeps out noise.

Four-channel IB card plugs into any IBM-AT compatible computer. It may be user-populated with any combination of Synchro/Resolver to Digital and/or Digital to Synchro/Resolver converters with industry-standard pin-outs. Internal micro-transformers isolate signal and reference lines, isolate field wiring from bus, and provide noise immunity. This preserves integrity of bus, and eliminates concerns...

Synchro/Resolver Modules are PC104 compliant.

PC104-DS Series has 2 channels of digital to synchro and digital to resolver conversion in stack-through PC104 footprint. Units feature 16-bit resolution, transformer isolated reference inputs, and short-circuit proof outputs capable of driving up to 1.2 VA load per channel. BIT inputs and Enable outputs are facilitated for direct compatibility with synchro amplifiers when driving loads up to 300...

A/D Converter has low power dissipation of 450 mW.

SPT7722 8-bit 250 MSPS A/D converter, with DLE of Ã-

Frequency Converter transforms single phase to three phase.

Compact BL3X350 delivers 350 VA per phase of clean, regulated 3-phase ac power from single phase input. Digitally controlled waveform produces clean power while protection circuitry provides for voltage fold back during overloads to maintain undistorted waveforms. Switch selectable, single phase input accepts 115 or 230 Vac at 47-440Hz, so it can accept any worldwide, shipboard or aircraft single...

Analog-to-Digital Converter has 28-pin flat package.

Model 9042 12-Bit monolithic analog-to-digital converter microcircuit offers 100 krad (Si) total dose tolerance, and utilizes radiation-hardened RAD-PAKÃ-® packaging technology. Designed with wideband front end, it addresses needs of multichannel receivers. 9042 runs off of one 5V supply, provides CMOS-compatible digital outputs at 41 MSPS, and maintains 80 dB spurious-free dynamic range...

Tekna Manufacturing LLC Announces NFPA 99 Compliant Model 7200 Multiplace Chamber

Tekna is a leader in Monoplace and Multiplace Hyperbaric Chambers for Hyperbaric Oxygen Therapy (HBOT), offering products that set the standard for quality and innovation. Our new 7200 series of multiplace chambers is a state-of-the-art system that integrates advanced engineering with a plethora of features and options making it the industry's premier HBOT system. To learn more, see our video.