Utility Knife and Blades offer safety and comfort.
Miscellaneous Blades

Utility Knife and Blades offer safety and comfort.

BAHCO® brand Utility Knife is made of heavy-duty zinc castings, incorporating rubber-molded grip for comfort and control. Measuring 6Â-½ in., unit includes large blade release knob that allows access for blade replacement and storage. Three-position blade adjustment switch provides different blade point settings. Measuring 2¼ in., No-Point(TM) Utility Blades offer safety by...

Read More »
Reciprocating Saw Adapters plug into brand name saws.
Saw Blades

Reciprocating Saw Adapters plug into brand name saws.

Suited for automotive bodywork applications, Flush-Cut Adapters for cutting, rasping, and sanding allow users to make cuts in hard-to-reach places. They also permit rasping and sanding from flush surface in tight spots, without bending blades or damaging materials. Tools, able to reach behind trim and framing members, are useful in projects from framing to finishing.

Read More »
Grit Hole Saw resists snags, heat, wear, and abrasion.
Saw Blades

Grit Hole Saw resists snags, heat, wear, and abrasion.

Grit Hole Saw features tungsten carbide cutting edges that are permanently bonded to alloy blade body, making it suited for cutting surfaces that are too hard, abrasive, or thin for standard bi-metal hole saw. Ranging in size from 3/4 to 6 7/8 in., saw is suited for cutting cast iron, composites, drywall, plaster, stucco, ceramics, fiberglass, and hardwood.

Read More »
Hacksaw offers blade change ability with pre-tensioning.
Saw Blades

Hacksaw offers blade change ability with pre-tensioning.

FatMax® High Tension Hacksaw features adjustable thumb-dial tension mechanism that provides tension memory and one-piece design that permits tension settings up to 330 lb. Power load sliding tension mechanism increases leverage and provides greater control when releasing blade, while 24 tpi, bi-metal blade allows for flush cutting with 4.75 in. depth cutting capacity. Die-cast, slope-nosed...

Read More »
Metal Cutting Blades cut ferrous and non-ferrous metals.
Miscellaneous Blades

Metal Cutting Blades cut ferrous and non-ferrous metals.

Constructed with vibration dampening geometry, Endurance® Carbide Tipped 8 in. Metal Cutting Circular Saw Blades resist bending and twisting and do not produce clouds of abrasive dust. They deliver straight cut with clean, burr-free edge with minimal heat and sparks. Blades with 42 teeth are recommended for metals over 3/32 in. thick, while 50-tooth blades are suited for thinner materials....

Read More »
Miscellaneous Blades

Bucket Blade Scraper is made of 100% recycled rubber.

Rubber Bucket Blade Scraper uses adjustable-slide channel, allowing heavy-equipment operators to adjust position of bolts within channel to match existing bolt pattern on plow. Rubber sections, reinforced with tough plies of nylon and steel, are compressed onto 1Â-¼ in. steel rod and secured every 12 in. using flatbar retaining plates. Adjustable heel pads help level scraper and extend life...

Read More »
Hub Blades offer solution for dicing low-k wafers.
Miscellaneous Blades

Hub Blades offer solution for dicing low-k wafers.

Nova(TM) Hub Blades incorporate formulations of diamond concentration and nickel bond to reduce chipping and peeling common in low-k wafer dicing. High yields are achieved even while advancing wafers through process at standard production feed rates. Product offered in different formulations to address requirements of various low-k wafer materials.

Read More »
Saw Blades

Gas Saw Blades are triple-reinforced.

Available with 20 mm and 1 in. arbor hole sizes, 14 in. metal and ductile gas saw blades measure 5/32 in. thick. Blades are constructed with 3 layers of fiberglass reinforcement for increased strength on the sides of the wheels. DSA approved blades are available in 2 grains: aluminum oxide, for metal/steel applications, and aluminum oxide-silicon carbide mix, for working with ductile iron.

Read More »
Bi-Metal Band Saw Blades have neutral rake tooth design.
Saw Blades

Bi-Metal Band Saw Blades have neutral rake tooth design.

Valu-Pac bi-metal band saw blades are offered in packages containing 3 blades with identical pitch, width, and length. They incorporate 8% matrix cobalt cutting edge for resistance to tooth chipping and neutral rake tooth design for additional tooth strength. Products are offered in 1 in. width with 4-6 or 5-8 pitch and 1Â-¼ in. width with 3-4 or 4-6 pitch. Multi-pitch teeth reduce noise...

Read More »
Carbide-Tipped Saw Blade cuts case hardened materials.
Saw Blades

Carbide-Tipped Saw Blade cuts case hardened materials.

HRc Carbide® band saw blade features 0° rake angle. It is offered in standard positive tooth form for aggressive cutting or Vari-Tooth® positive design for less vibration and quieter cutting. Sizes include 1Â-¼ x .042, 1½ x .054, and 2 x .063 in. Carbide tipped teeth can cut through induction hardened chrome plated shafting, case hardened materials, and difficult to...

Read More »

All Topics