Power Jacks Limited
Fraserburgh, Aberdeenshire AB43 8TE GBR
Share:
Clock Oscillators support fibre channel data storage.
CB3 106.25 MHz clocks are available in stability grades of 25, 50 and 100 ppm. They are offered for 3.3 and 5.0 Vdc systems and draw 40 and 50 mA, respectively. Output is CMOS compatible and includes output enable/disable feature. Four-pad, 5mm x 7mm surface-mount oscillator packages are compatible with SMT pick-and-place assembly equipment. Temperature ranges include 0 to 70Ã-
Read More »Vehicle Restraint requires no external power.
DOK-LOK RHR-1000 vehicle restraint is designed with 9 in. low-profile carriage able to capture wide range of trailer rear-impact guards (RIG). Articulating nose extension allows carriage to travel low to ground to avoid damage to restraint or RIG. RHR-1000 employs Universal Restraint Controller technology for interconnecting controls with other powered dock equipment. Other features include...
Read More »
Miniature Relays consume very little power.
Model AZ852 and AZ853 relays meet Bellcore's 2.5 kV and FCC Part 68 1.5 kV surge voltages standards, plus IEC 60950, UL1950 and EN60950 spacing and high breakdown voltage requirements. Both consume only 79 mW power at pick-up, have stable contact resistance for signal or low-level switching, and are epoxy-sealed for automatic processing. Versions with latching coil and/or SMT enclosure are...
Read More »
Thermocouple Input Module fits company's micro PLC.
Model TC1 11 T/C module clips onto side of T1-16S micro PLC, allowing alarming, monitoring or PID control functions based on temperature. It accepts inputs from type K, E, J T/Cs or millivolt sensors. Module is isolated via photo-coupler and dc/dc converter and has built-in functions including linearization, cold junction compensation, and burn-out detection. Each PLC can accommodate up to 8 I/0...
Read More »
Indicator can be adjusted from 100 to 1999 counts.
DIS471B-24 process indicator, available with dc voltage and current inputs to monitor process signals, features auxiliary 24 Vdc (35 mA maximum) power supply for powering external equipment. Digit display has 0.56 in.-high red LED indicators. Indicator mounts through front panel in 1/8 DIN cutout. When properly mounted, it meets NEMA-4 requirements for being liquid-tight. Unit includes selectable...
Read More »
Vane Pump handles high-volatility fluids.
MagnatexÃ-® MPT Regenerative Turbine Vane Pump is a magnetically driven, sealless pump featuring a regenerative turbine vane impeller and rare earth Neodymium magnets for synchronous drive with no slippage. Close-coupled design eliminates alignment problems. Pump is capable of operation under 2 ft of static NPSH at line pressures up to 100 psi and flow rates of 2-3 gpm.
Read More »
Screener is designed for in-line operation.
VibroscreenÃ-® Circular Vibratory Bag Dump Screener scalps bag scraps and oversized materials from manually dumped bulk materials while protecting operator and plant environment against dust contamination. Ambient air and dust from dumping activities is drawn onto exterior of 2 cartridge filters that derive vacuum from top-mounted exhaust fan. Screener is offered in 24, 30 and 40 in....
Read More »
Encoders feature digital ASIC technology.
Model 771 and 776 Thru-Bore Series Accu-Coders(TM) have bore sizes to 1.875 in. and are suitable for motor feedback, velocity, positioning and servo control applications. Model 771 mounts directly on NEMA C-Face motors and features C-Face mount on both sides. Model 776 is 1.36 in. deep and ideal for space restrictive applications. Encoder-on-a-chip design provides noise immunity necessary for...
Read More »
Male Connectors are designed for use in backplanes.
Type D Vertical Male Connectors are 8+2-row x 25-position headers that provide up to 220 signal contacts evenly distributed on 2 mm grid. They are UL approved and comply with requirement of IEC 917 and IEC 61076-4-101 specifications. Featuring multipurpose center incorporating pre-alignment guides, connectors feature press-fit design for gas-tight connection to PC board and are available in a...
Read More »
Parts-Cleaning Systems meet EPA guidelines.
OmegaÃ-® systems use non-toxic soaps and ultrasound to automatically degrease, clean and prefinish parts and components. Units feature fully insulated tank bodies and non-immersion, silicone blanket heaters. Models include Omega ProÃ-® at 1000 W of ultrasound power with 3.5 cu ft bath, Omega Pro PlusÃ-® at 2000 W with 5 cu ft bath, Omega Pro ForceÃ-® at 2000 W with 7 cu ft bath,...
Read More »