Sokymat SA
Granges CHE
Share:
Crimping Tool handles big terminals.
Lightweight Sta-Kon ERG-2008 Comfort Crimps tool is UL-listed for handling tubular, non-insulated Sta-Kon terminals ranging from 8 through 1/0 AWG. It does same job as company's heavier, bulkier tools but with shorter, ergonomic frame; less required force; and comfortable, rubberized thermoplastic handles. Rotating crimp die nest marked for each specific wire size and Shure-Stake(TM) mechanism in...
Read More »Restraint keeps trailer at dock.
TRUK STOP STAR 4 effectively prevents premature trailer departure, trailer creep, and trailer landing gear collapse. Hydraulic powered device has restraining force of 30,000 lb and can hook and hold any style ICC bar. Its sensor bar communicates to control panel actual hook contact with ICC bar. Restraint is compatible with new federal regulations and with any design dock leveler equipment.
Read More »
Combustion Analyzer suits various feuls.
Series CA-6100 CA-CALC provide real-time analysis of residential to light commercial gas/oil/wood heating systems and other combustion appliances to tune burners for optimum efficiency and safe operation.
Read More »
Electric Generator produces 6,100 W.
DP6000 can run for 12 hr at half load and 9 hr at full load. It has electric start 12-hp Kohler engine with cast-iron cylinder sleeve and quiet muffler. Low-oil shutoff helps extend life while automatic idle control provides better fuel economy and helps prevent surges when operating power tools. It has maintenance-free, brushless alternator; GFCI protection; hourmeter; and overload indicator....
Read More »
Hedge Trimmer weighs 12 lb.
H20D has adjustable swivel handle that rotates 40 and 90 deg in either direction for user comfort and increased cutting performance. It has 2-cycle, 1.05 hp engine, two-shoe clutch, and 24 in. dual-sided, double-reciprocating blade that cuts branches up to 1 in. thick. Low-tone muffler and air silencer provide lower sound levels and increased operator comfort. It has primer bulb for fast...
Read More »
Imprinter marks on any flat surface.
CC Series prints on cartons, caps, labels, metal parts, cans, and bags for top, side, or bottom coding. It can be used as semi-automatic marking system or works in fully automatic mode when mounted on form and fill system. Quick-change type holders allow frequent changing of print message, while calibrated ink cartridge holder allows better adjustment for consistent clear, sharp, and legible...
Read More »
Grout protects cables.
Cement-based nonshrink Five Star Special Grout 400 for cables and tendons provides corrosion protection. It meets Guide Specification for Grouting of Post-Tensioned Structures and testing requirements for Class A, B, C, and D grouts, prepared by Post-Tensioning Institute's Committee on Grouting Specifications. Typical application is in bridge construction, where material is pumped for long...
Read More »
Op Amps feature improved slew rate/power ratio.
MIC920 has gain-bandwidth product of 80 MHz and slew rate of 3000 V/microsec. MIC921 has gain-bandwidth product of 45 MHz and slew rate of 3200 V/microsec. Both can drive unlimited capacitance, are housed in SC70-5 packaging, and are specified for supply voltages of +/-2.5 V and +/-9 V. Applications include video and imaging equipment, and portable instrumentation.
Read More »
Helium Ionization Detector provides on-site analysis.
D3-1-HP Pulsed Discharge Helium Ionization Detector is non-radioactive, non-destructive, highly sensitive, and universal. Response is linear over wide range, and MDQs for most compounds are in low ppb range. With no open flame, no hydrogen requirement, and close-to-true-mass response, D3-1-HP is suitable for FIDs in petrochemical environments. When helium discharge gas is doped with suitable...
Read More »
Power Entry Module exceeds power limits.
EF Series includes AC inlet and circuit breaker, UL rated up to 20 A at 250 V. Circuit breaker provides manual reset of circuit and status indication depending on switch position (I/O). It is recessed in flange to protect against inadvertent actuation. Filter options meet standard and medical grade attenuation requirements at 12, 16, and 20 A. Direct electrical contact of filter to chassis...
Read More »