Rohde & Schwarz GmbH & Co
- DEU
Share:
Machine Control comes on single PCI card.
MachineLogic(TM) Slot Card Runtime has IEC 61131 programming languages, simultaneous communications between DeviceNet or Profibus fieldbus I/O and Ethernet I/O, and its own processor and real-time operating system for deterministic, real-time performance. Card continues to run even if host computer is re-booted. Programming is via MachineLogic environment that has 5 different IEC 61131 shop-floor...
Read More »
HMI/SCADA Software provides historical data organization.
Lookout v5.0 offers historical data viewing and management capabilities in presenting, archiving, and organizing historical data. In addition to saving locally, users can save data to remote server or database as often as they want. Users can also merge historical data for side-by-side analysis. Lookout v5.0 simplifies industrial automation by eliminating programming, scripting, and separate...
Read More »
Silicone Material eliminates static buildup.
Semi-conductive Silicone C material is suitable for use on drive and label rollers, and can also be used in direct thermal printing applications. Resistivity is rated down to E9-E12 ohm-cm, and durometers range from 30 to 60 Shore A. Material can withstand 300 to 400Ã-
Read More »
Pushbutton Switch is rated to IP67 and IP65.
Double-sided, glass-mountable pushbutton switch includes choice of red, green, or yellow halo LED illuminations. LED is rated at 24, 36, 48, 72, or 110 Vdc, and has minimum life of 100,000 hours. Pressel area can be supplied with raised symbols or engraved, and operating surface meets disability and Rail Vehicle Accessibility regulations. Switch is rated at 137Vdc/200mA maximum and 5VdcC/5mA...
Read More »
Variable Frequency Drives control ac induction motors.
EagleDrive1(TM) Series and EagleDrive3(TM) Series provide variable speed control of single-phase and 3-phase motors, respectively. EagleDrive1 is available in 115 V and 230 V at power levels up to 1.5 hp. EagleDrive3 is available in 200-240 V at power levels up to 3.0 HP, and in 380-480 V at power levels up to 120 HP. Drives have pushbutton keypad, simple programming, 95% drive efficiency,...
Read More »42 Lubricating Fluids extend equipment life.
Molykote(R) industrial fluids are made of synthetic fluids and ultra-high purity mineral oils that reduce lubricant consumption, permitting longer drain intervals and extending equipment life. Additives reduce oxidation rates due to elevated pressures and temperatures that can cause premature lubricant breakdown. Fluids are resistant to oxidation and emulsion.
Read More »
Position Controller works with valves and other devices.
EMPC electronic controller is suited for company's valves, and can be adapted to other systems. It has adjustable setpoint, proportional band, PID and temperature offset, and provides operation within narrow bands with no hunting or overshooting. Compact controller is easy to set up and tune, and has no motors, gears, lead screws, or solenoids. Controller has 24 Vac/dc power input and output,...
Read More »
Roll-Fed Labeler runs at high speed with improved safety.
Enhanced BH8000 operates at speeds of more than 800 cpm, yet is safer than previous model. Vacuum Drum blows label off during machine set-up, eliminating need for operator to reach into moving components. Automatic spring-back glue roller pulls gluewheel away from vacuum drum in case machine loses air pressure, preventing vacuum drum damage. It handles container sizes from 220 ml to 3 L....
Read More »
Tactile Switches are illuminated.
JF Series full-face, LED illuminated, thin tactile switches are suitable for applications that require operator interface, such as front panels and custom keyboards. LEDs are available in red, green or yellow, and actuator color matches to further enhance illumination. Switches measure 7.3mm from PCB to top of switch, and total surface area covers 0.697 X 1.059 in. Single pole, single throw...
Read More »
Round Insert Cutter offers productivity ratio of 10:1.
CoroMill(R) 300 round insert cutter is suitable for machining of materials from soft aluminum to hardened steel. Designed for multi-axis milling, CoroMill 300 is available in long shank versions for machining deep closed pockets and narrow cavities with shallow radial and axial cuts. Available diameters range from 0.375 to 0.750 in. Precision ground inserts are available in carbide grades GC1025,...
Read More »