European Powder Metallurgy Association (EPMA)

Market Street
Shrewsbury GBR

Bending/Forming Machines make multiple bends in a single plane.

ET 95 vertical and horizontal press tube bending/forming machines can produce square, rectangular, U and compound shapes on round, square, rectangular and other profile tubing or flat and bar stock. They have bending tonnage of 14-58 tons and bend radii of 2 to 6 in. with tube diameters from 2.5 to 3 in. and wall dimensions from .035 up to 1 in. O.D. and .180 up to 3 in. O.D. Controls include...

Material Handling & Storage

Large Crane handles rough terrain.

The 130 ton RT9000E crane provides mobility, maneuverability and pick-and-carry capabilities. It has a five section 42 to 160 ft boom that provides a 169 ft maximum tip height and 140 ft maximum radius with 3,770 lb capacity. Cab has tinted safety glass, armrest-mounted single-axis controllers, hot water heater, air fan, sliding side and rear windows, sliding skylight with electric wiper and...

Agricultural & Farming Products

Motion Chip controls four axes at a time.

PCD-4541 4-axis motion control chip is for 2-phase unipolar or bipolar stepper motors. Sequence logic for full and half step modes is built-in, so it can output CW/CCW pulses or excitation signals directly to drive chips. Chip provides independent axis control, simultaneous start and stop of all axes, linear or S-curve acceleration and deceleration, speed change on the fly, idling pulse output...

Construction Equipment and Supplies

Cylinders are available with bore sizes from 3/4 to 8 in.

Q6 Hydro-Line Cylinders come with pressure-energized nitrile rod seals and nonmetallic piston wear rings. Pre-lubricated from factory, cylinders are suitable for non-lubricated air service up to 250 psi. Q6 NFPA-interchangeable cylinders feature precision-machined aluminum end caps and self-aligning, externally removable rod cartridge assemblies. Hydraulic HQ6 tolerates pressures to 400 psi, and...

Mechanical Components and Assemblies

Bridge Handles feature counter bored mounting holes.

ErgostyleÃ-® Bridge Handles are made from glass-fiber reinforced technopolymer plastic with black matte finish, while mounting holes are counter bored for socket cap screws and have technopolymer plastic cover caps available in variety of colors. Slight bend in handle distributes force on fingers during use. Resistant to solvents, oils, grease, and other chemical agents, handles are also...

Cement Resurfacer dries in 24 hours.

P-205 EASY-FIX thin pavement overlay repairs uneven concrete surfaces, and is suitable for permanent repairs to sidewalks, drives, aprons, docks, and ramps. Able to resist freeze/thaw cycles, it adheres to damp surfaces. De-icing salts and water will not penetrate it. Application is accomplished via broom for textured, concrete, gray, non-slip surface that dries in 24 hours.

Parylene System modifies pressures and dwell times.

PDS-2060PC Parylene deposition system, with integrated personal computer for programmable control, allows users to establish and refine programs that direct each phase of Parylene coating cycles. System includes on-board personal computer, fold-out keyboard, flat-screen monitor, and printer that operate under Labview(TM) software. Proprietary software prompts users for each parameter from vacuum...

Safety & Security Equipment

Hardhats meet ANSI Z89.1 Class E standards.

Head-Turners(TM) hardhats are offered in 2 designs which withstand temperature variances, humidity and exposure to UV light for long-lasting wear. NightVision(TM) design is fully reflective for added protection in low light environments and is ideal for nighttime road construction. Both American Flag and NightVision have 4-point ratchet suspension fitting head sizes 6-1/2 to 8. Hats are fully...

Test & Measurement

Flowmeter is accurate to -

Vortex Flowmeters feature turndown ratios of up to 80:1. Their dual signal processing technology independently measures each vortex on either side of bluff body and eliminates noise. Vortex Flowmeters are available in both inline and insertion versions. Inline versions are available with ANSI and DIN flanges.

Agricultural & Farming Products

Stripper/Cutters have cushioned handles.

With Klein-Kurve(TM) double-dipped handles, Model 11055 and 11057 are designed for stripping, cutting, looping, and gauging solid and stranded wire. Model 11055 is designed for 10 to 18 AWG solid and 12 to 20 AWG stranded wire; Model 11057 is designed for 20 to 30 AWG solid and 22 to 32 AWG stranded wire. Both cleanly shear 6-32 and 8-32 screws. Other features include serrated nose jaws and...