Aprima Medical Software, Inc

3330 Keller Springs Suite 201
Carrollton, TX 75006

Isolation Valve mounts directly on manifold.

Two-way solenoid valve mounts on manifold, is rated up to 35 psi with Cv of 0.05, and is available in 12 and 24 Vdc models, in normally open or normally closed versions. Materials in contact with flow path are limited to PEEK (polyetheretherketone) and EPDM (ethylene propylene) or FKM (highly-fluorinated fluorocarbon). Applications include blood analysis, clinical chemistry, DNA processing,...

Fluid & Gas Flow Equipment

Inert Valve controls corrosive or high-purity fluids.

Solenoid-operated IPV inert proportional diaphragm isolation valve can be used in medical equipment, water purification and clinical chemistry industries. Materials of all surfaces in flow path are inert and impervious to wide range of aggressive fluids. Valve provides infinitely variable flow control, is rated to 60 psi, and has 24 Vdc driver. Poppet and seat are configured to provide bubble...

Fluid & Gas Flow Equipment

Inert Diaphragm Valve handles aggressive fluids.

Three-way IDV solenoid-operated diaphragm isolation valve works with fluids found in medical equipment, water purification and clinical chemistry industries. Materials of all surfaces in flow path are inert and impervious to many aggressive fluids. Valve is typically used in waste circuits where valve must tolerate high contaminant levels. Valve is rated 35 psi with Cv of 0.22 and is available in...

Communication Systems & Equipment

Ultrasonic Positioner measures travel of valve blade.

EP 2000 compares valve position to valve control signal, and provides valve open, valve closed, positioner start, positioner stop, and valve blade not in position indications. It works with 4 to 20 mA signal from DCS system, where at 4 mA signal valve is completely closed, at 20 mA completely open. Probe can also be trained to use 4 to 20 mA signal for partially opening and closing valve.

Fluid & Gas Flow Equipment

Through-port Valves control and shut off flow.

Stargate-O-Port valves work with ultrasonic positioner to control flow. Different port and orifice shapes allow selecting certain characteristics of flow cross section and blade position. Valves also serve as line blind in maintenance situations, to take out pipes and set blank flanges for safety. They have tight class VI shut-off which allows operators to close valve, inset locking pin and pad...

Chemicals & Gases

Screen Changer keeps media flowing through filter.

Big Screen automatically changes screens when filter clogs up with particles without slowing production. Actuator moves screens, bringing one which is to be exchanged outside screen body and clean one into flow area. While one screen is outside body it can be cleaned and prepared for next exchange. Changer accommodates screen sizes from 2 to 72 in. dia with different hole sizes, different spacing...

Electrical Equipment & Systems

RF Test Sockets keep the pressure on.

Spring-loaded lids on radio frequency (RF) test sockets provide consistent lead pressure. Precise pressure requirements can be met with mix-and-match springs from 1/2 to 25 lbs. Each socket comes with floating leadbacker built into every lid, and lids can be used throughout RF/microwave, automated handling and burn-in/life testing applications. Each socket has Microstrip Contacts, which can be...

Test & Measurement

Spectral Reflectometer works in a vacuum.

Spectral Reflectometer measures absorbance, transmittance and reflectance and performs spectral analysis to better than Ã-

DC/DC Converter meets safety standards.

ASDH series of open frame 5, 7 and 10 W dc/dc converters are approved for EN60950 and UL1950 SELV safety standards. Converters are available in 48 models with input ranges of 9 to 36 Vdc and 18 to 75 Vdc, with single and dual outputs from 3 to 15 Vdc. Each has 1,500 V I/O isolation, and works in temperatures of -25Ã-

Flexible Hose and Ducting have cuff ends for easier clamping.

Flexible Hose Cuffed Ends have smooth, elasticized finish and are molecularly bonded without adhesives to provide smooth clamping surface. Eliminating wire helix interference for tighter seal, finished cuff ends install over fittings and can be made from same material as hose or ducting. Available for urethane, thermoplastic rubber, and TPR coated fabric hose and ducting, ends can be bonded to...