Aprima Medical Software, Inc

3330 Keller Springs Suite 201
Carrollton, TX 75006

Conveyor Gate retracts to increase flexibility and safety.

Cantilevered Gate is a retractable conveyor bed with self-supporting design and spring/shock technology. Gate section is used to temporarily halt conveyor flow and allow people to pass through line. Conveyor retracts into floor support and adjustable bed angle optimizes product flow and fine tunes for different applications. Typical configurations include gravity wheel and powered roller beds...

Software

Human/Machine Interface Software eases regulatory compliance.

RSView Enterprise Series(TM) v3.0 HMI, which includes RSView Supervisory Edition(TM), RSView Machine Edition(TM), and RSView Studio(TM), supports productivity through redundancy and information collaboration as enabled by FactoryTalk(TM). Common design environment allows developers to migrate and re-use projects, tools, and graphics between machine- and supervisory-level platforms. FactoryTalk...

Material Handling & Storage

Vibratory Rollers achieve centrifugal force of 19,125 lb.

Series C810C includes 7,275 lb Model C815C for granular and mixed soil applications, and 7,385 lb Model C812C with 70 contact pads for cohesive and semi-cohesive soils. Dual travel pump system, rear travel axle with no-spin differential, and radial piston drum-drive travel motor allow gradeability of 55%. Both models utilize 50 hp Deutz F3L 2011 air/oil-cooled diesel engines, and include dual...

Pushbutton Switches withstand frost and icing conditions.

Series IF momentary pushbutton switches feature 1.180 in. diameter black or red panel mounting bezel with rubber-like actuator that provides 500,000 cycles of life at full load in temperatures from -20 to 85Ã-

Laboratory and Research Supplies and Equipment

Tube Conditioning Unit simultaneously cleans up to six tubes.

Model 9600 cleans/conditions sorbent tubes off-line. Stand-alone module accommodates tubes with mixed sorbent packings, sizes, and lengths and allows users to individually set flow rates, temperatures, and conditioning times. Standard unit has six heating jackets that accept Ã-¼ in. OD tubes up to 11.5 cm in length. Temperature control zones can be programmed in 1Ã-

Portable Tools

Gang Boxes are approved for wet and damp locations.

Single and Two Gang Boxes feature continuous and seamless die cast construction to stop entry of damaging dirt, dust, and moisture. Powder coating assures uniform weatherproof durability, while tapered hubs prevent wire abrasion. Boxes are furnished with closure plugs, ground screws, and mounting lugs. They fit weatherproof covers in standard trade sizes and are suitable for interior and exterior...

HVAC

De-Icing Systems come engineered and assembled.

Copper-FinÃ-® Car Wash Bay De-lcing Systems include all piping to meet specific application. Circulating pump, air separator, charged expansion tank, and all controls are mounted and wired. Copper tube design uses 2-pass heat exchanger. Water is circulated through row of finned copper tubes, creating scouring action that prevents sediment and lime scale build-up. Gasketless design eliminates...

Printing & Duplicating Equipment

Digital Printer performs case and bag printing.

MAXIMIZER prints text, bar codes, and graphics on uncoated multi-wall kraft bags, flat cases, die cuts, and blanks. Unit includes vacuum feeder that allows operators to switch from one type of print job to another as well as lift table magazine that holds up to 100 bags or 60-90 single sheet die cuts. It prints one side at a time in one color. Computer generated printing stencil allows placement...

Fluid & Gas Flow Equipment

Stationary Air Compressor utilizes microprocessor control.

Model LS-20 utilizes one single-stage, 100 hp rotary screw compressor with tapered roller bearings on discharge end and cylindrical roller bearings on inlet. Fluid-lubricated and cooled, product is offered in four models from 344-490 acfm with pressure ratings of 100-175 psig. Features include multi-stage air/fluid separation, flange-mounted motor and air end, and heavy-duty air inlet filter....

Machinery & Machining Tools

Injection Molding Machines range from 720-1200 tons.

Series em combines electric and hydraulic features for reduced cycle times. Two-platen mechanism provides accurate mold clamping, while linked split nut drive results in simultaneous actuation. Peakless Pressure Control eliminates high-pressure spikes at end of fill during high-speed injection. Long platen supports resist tilting and ensure parallelism of moving platen and mold. MAC-VIII control...