Gemalto
92447 FRA
Share:
![Accelerometer measures vibration on structures.](https://cfnewsads.thomasnet.com/images/medium/828/8289.jpg)
Accelerometer measures vibration on structures.
Ultra miniature ceramic shear accelerometer type 8778A500 offers 10 mV/g vibration measurement sensitivity, 0 to 500 g measuring range, and a Ã-
Read More »![Clear Polymer helps avoid indutrial battery breakdown.](https://cfnewsads.thomasnet.com/images/medium/829/8293.jpg)
Clear Polymer helps avoid indutrial battery breakdown.
UDEL(R) P-1700 transparent thermoplastic polymer exhibits resistance to moisture absorption, shock, and vibration. Heat deflection temperature is 345 deg F. Transparent, opaque, and glass-fiber reinforced grades of UDEL polysulfone can be used for injection molding into complex parts or extrusion into forms such as rod, film, sheet, profile, and tubing. UDEL polysulfone resin can also be...
Read More »Friction/Wear Material suits non-lubricated applications.
Polyamide-imide TORLON(R) 4435 PAI provides wear resistance in high-PV, 50,000 to 100,000 psi-ft/min applications. It also exhibits wear resistance in low-pressure, high-velocity conditions (125 psi and 800 ft/min) and high-pressure, low-velocity conditions (2,000 psi and 50 ft/min). Glass transition temperature allows parts to operate continuously at temperatures up to 260 deg C. Thermoplastic...
Read More »High-Temperature Resins suit critical electronics applications.
Flame-retardant AMODEL FR-4133, FR-6133 and FR-6145 polyphthalamide resins are useful in lead-free SMT soldering operations. They are available in hot-water-moldable base resins, 4000 and 6000, and 2 glass-reinforced levels, 33 and 45%, with heat distortion temperatures up to 300 deg C. Applications include connectors, chip capacitors, cell phone components, circuit breakers, contactors, relays,...
Read More »![Torque Transducer mounts in-line to SAE or Metric flanges.](https://cfnewsads.thomasnet.com/images/medium/829/8297.jpg)
Torque Transducer mounts in-line to SAE or Metric flanges.
Non-contact, rotary Model RTC sensor transmits torque signal to RF receiver, delivering output of 0 to 10 V, proportional to torque, or optional 4 to 20 mA output. Operating range is 1,500 to 170,000 in.-lb, with running speeds up to 15,000 rpm, depending on range. RF telemetry package is induction-powered by stationary loop antenna coupled to power supply and receiver. Transmitter may be...
Read More »![Relay Output Module clips onto microPLC.](https://cfnewsads.thomasnet.com/images/medium/830/8302.jpg)
Relay Output Module clips onto microPLC.
RO108M attaches to side of Series T1-16S microPLC and can switch/control 100 to 240 Vac or 5 to 24 Vdc. Each T1-16S accommodates up to 5 relay output modules. TRO108M can be used wherever it is necessary to have relay contact switch ON/OFF in control circuit. It allows T1-16S to control, alarm, or monitor based on system conditions, including: Turn ON/OFF motors, solenoids, or interposing relays;...
Read More »![Wastewater Evaporator eliminates discharge to drain or sewer.](https://cfnewsads.thomasnet.com/images/medium/830/8303.jpg)
Wastewater Evaporator eliminates discharge to drain or sewer.
HYDRO-VAP(TM) 1000E runs at 3 to 4 gph to provide 95% reduction in wastewater. Evaporator heats wastewater to boiling and turns it into vapor. Harmless water vapor is vented through blower-assisted stack and exhausted to outside atmosphere.
Read More »![Parts Washer cleans with hot water.](https://cfnewsads.thomasnet.com/images/medium/830/8304.jpg)
Parts Washer cleans with hot water.
Model 45E Aqueous Parts Washer cleans parts with hot water, biodegradable detergents, and high-flow nozzles. Parts are usually clean and ready for use in 10-15 min. As needed, its Wastewater Disposal System evaporates wastewater and can reduce waste stream up to 95%.
Read More »![Conveyer Parts Washer automates cleaning.](https://cfnewsads.thomasnet.com/images/medium/830/8305.jpg)
Conveyer Parts Washer automates cleaning.
Model LM-400 Aqueous Conveyer parts washer has 4 x 6 ft footprint, allowing unit to provide part wash, wash-rinse or wash-rinse-dry cycle directly in line with parts-movement/production-line. Cost savings are realized in reducing number of employees needed to clean parts and by freeing up parts cleaning employees to work in other areas.
Read More »![Polyimide Parts meet outgassing and ionic purity standards.](https://cfnewsads.thomasnet.com/images/medium/826/8267.jpg)
Polyimide Parts meet outgassing and ionic purity standards.
Pyropel HD thermoset polyimide machining stock, suitable for manufacturing parts subject to high temperatures or chemical attack, offers temperature resistance to 550 deg F. It is available machined to print or in standard 12 x 12 in. plates in thicknesses up to 1 in. Applications include metal welding and cutting equipment; wafer processing equipment; soldering fixtures; high-pressure thermal...
Read More »