Invensys Process Systems
London SW1E 5BF GBR
Share:
Proportional Valves feature close tolerance spools.
DFW proportional, directional control valves can be used for reproducible control of actuator speed in rapid/slow speed profiling as well as smooth acceleration and deceleration. D1FW features flow rating to 12.5 gpm, while D3FW has flow rating to 45 gpm. Connection options include conduit boxes with wire leads, flying leads or DIN-type connectors.
Read More »Cal-Gas Standards Generator calibrates gas analyzers.
Model 491MB Gas Standards Generator is designed to calibrate gas analyzers such as gas chromatographs, mass spectrometers, and ion mobility spectrometers. 491MB uses Trace Source(TM) Permeation Tubes to generate low concentrations (1000 ppm to ppb) gas standards for VOCs, Acid Gases, Amines, Sulfurs, and Hydrocarbons (400+ compounds). Standards are traceable to NIST.
Read More »Sensors measure micro liquid flow rates.
Rated for operation up to 500 psig, Series 102 liquid flow sensors measure flow rates from 13 mL/min to 10 L/min (2.6 GPM) with Ã-
Read More »Continuous Solvent Vapor Monitors reduce exhaust airflow.
670 Series Continuous Solvent Vapor Monitors are placed at source of emissions. Continuous monitoring allows air recirculation in processes to reduce exhaust airflow. Incinerator has less air to process, therefore requires less fuel. Additionally, 670 Series meets safety standards set by NFPA to protect incinerator as well as employees.
Read More »Precision Ground Insert has 3F geometry.
Precision ground insert with 3F geometry for stainless steels, aluminum, high-temperature alloys and steels features periphery ground edges for accurate profiling and indexability. Additional features include light hones and positive geometry. Radii are available for light depths of cut and producing small corner radii. PVD grades offer layer of lubricity for reduced coefficient of friction....
Read More »Hoses are ideal for half-bend radius applications.
Models 351TC and 351ST abrasion-resistant hoses, designed for 1/2 SAE 100R1 minimum bend radius applications, are available with MSHA-accepted Tough Cover or Super Tough polymeric cover. Both offer 4,000 psi constant working pressure in sizes that range from 1/4 in. to 3/4 in. I.D. They are constructed of oil-resistant, Nitrile-based synthetic rubber tube, with 2 braids of high-tensile steel wire...
Read More »Bending/Forming Machines make multiple bends in a single plane.
ET 95 vertical and horizontal press tube bending/forming machines can produce square, rectangular, U and compound shapes on round, square, rectangular and other profile tubing or flat and bar stock. They have bending tonnage of 14-58 tons and bend radii of 2 to 6 in. with tube diameters from 2.5 to 3 in. and wall dimensions from .035 up to 1 in. O.D. and .180 up to 3 in. O.D. Controls include...
Read More »Large Crane handles rough terrain.
The 130 ton RT9000E crane provides mobility, maneuverability and pick-and-carry capabilities. It has a five section 42 to 160 ft boom that provides a 169 ft maximum tip height and 140 ft maximum radius with 3,770 lb capacity. Cab has tinted safety glass, armrest-mounted single-axis controllers, hot water heater, air fan, sliding side and rear windows, sliding skylight with electric wiper and...
Read More »Motion Chip controls four axes at a time.
PCD-4541 4-axis motion control chip is for 2-phase unipolar or bipolar stepper motors. Sequence logic for full and half step modes is built-in, so it can output CW/CCW pulses or excitation signals directly to drive chips. Chip provides independent axis control, simultaneous start and stop of all axes, linear or S-curve acceleration and deceleration, speed change on the fly, idling pulse output...
Read More »Cylinders are available with bore sizes from 3/4 to 8 in.
Q6 Hydro-Line Cylinders come with pressure-energized nitrile rod seals and nonmetallic piston wear rings. Pre-lubricated from factory, cylinders are suitable for non-lubricated air service up to 250 psi. Q6 NFPA-interchangeable cylinders feature precision-machined aluminum end caps and self-aligning, externally removable rod cartridge assemblies. Hydraulic HQ6 tolerates pressures to 400 psi, and...
Read More »