Tacton Systems
Stockholm 111 22 SWE
Share:
Vacuum Dispersion System dissolves 100-1,500 ml of product.
CDS dispersion system, with clear glass cover, allows operator to observe dissolving process and product flow. System operates under vacuum with single-walled containers of 250, 500, 1,000 and 2,000 ml placed and secured in corresponding holding device. Height of dissolver shaft and dispersion impeller can be adjusted while dissolving under vacuum. Vacuum-shaft bearing can be adapted to fit most...
Read More »
Form Measuring Machine has measuring volume of 1 liter.
MarForm(TM) MFU 100 delivers lab-quality 3D and form measurements to shop floor. In addition to cylindricity, concentricity, and parallelism, MFU 100 measures diameter and angle on parts such as sealing cones. Motorized centering tilt table, in conjunction with T7W motorized probe and motorized Y-axis, provides fully automated measurement. MFU 100 is driven by MarWin form evaluation software,...
Read More »
Draw Latches feature compact, surface-mounted design.
Made with die-cast zinc bodies and stainless steel hardware, fixed-grip draw latches accurately position panels using operating latch that aligns panels and draws them together on same plane. Products also feature over-center latching mechanism to prevent accidental opening under stress or vibration. Measuring less than 7/8 in. high, products leave no exposed hardware on inside of door and...
Read More »
Digital Calipers/Micrometers offer water resistance.
Rated IP67, MarCal(TM) EW Digital Calipers feature resistant materials in casing and keyboard, and fluid protection system to safeguard electronic components. Offered in ranges from 6, 8, and 12 in., units include dirt wipers, lapped guide ways, and hardened stainless steel slide, beam, and measuring blades. Rated IP65, Digital Micrometer Models 16 and 40 EW feature satin chromed steel frames...
Read More »Horizontal Machining Center uses minimum quantity lubrication.
Near-dry Model RM80H features 80 mm diameter spindle capable of 8,000 rpm, and X, Y, Z axis travels of 20.8, 22.0, and 20.8 in., respectively. It provides deep hole drilling and rapid penetration up to 40 ipm, making it suited for forged steel and nodular iron crankshaft applications. System mixes air with fluid in spindle and applies droplets through tool to cutting surface. No more than 2 oz of...
Read More »
Hydraulic Toolholders offer radial length adjustment.
TENDO clamps different types of cutting tools with cylindrical shanks directly in toolholder without using intermediate sleeves. Clamping is done by steel sleeve surrounded by hydraulic fluid, and cutting tools with different shanks are held with concentricity of less than 0.002 mm. Hydraulic, completely closed system absorbs vibrations inherent in cutting or grinding processes, resulting in...
Read More »
Toolholding System provides alternative to collet style.
With run-out accuracy of 5 microns, SINO-T provides consistent support across entire clamping zone. Actuation is performed by using C-spanner wrench. Standard unit is fine balanced to G6.3 at 15,000 rpm. Available with CAT 40 and HSK-A 63 spindle interfaces, vibration-dampening system incorporates facility for Ã-
Read More »
Heatshrink Tooling provides high production toolholding.
CELSIO Tooling guarantees true running of 0.003 mm when checked at inside end of clamping bore. Steel bodies ensure maximum toolholder life without temperature distortion. Mounting tapers are ground to grade AT3 Form A, and high-temperature as well as hardening procedures help avoid material distortion due to heating and cooling. High-frequency, 10 kW induction coil delivers fast shrinking for...
Read More »
Detent Pins meet or exceed Mil-P-45952/1.
Kwik-Lok(TM) Heavy Duty Detent Pins are shoulder-style alignment pins for applications that do not require positive locking ball. Heavy-duty spring and 2 spring-loaded stainless steel balls provide high pullout force. Available in stainless steel and alloy steel, units range from 3/16-1 in. and 5-25 mm. Ring is included for attachment of optional lanyard.
Read More »
Balancing Machine is designed for toolholder systems.
Requiring 110 V power connection and 87 psi compressed air for operation, ACURO Plus can balance one complete system, consisting of toolholder and tool, within seconds in one or 2 planes. Adapter system with automatic clamping provides pulling forces equal to actual machine spindle. Balancing operations of toolholders with max weight to 33 lb and length to 13 -½ in. can be done at speeds of...
Read More »