Sherwin-Williams Co. c/o Ultimate Lead Systems    Berea, OH 44017
Jun 08, 2005 HYDROGLOSS(TM) Single-Component Urethane Coating is formulated to provide high-gloss finish with interior and exterior color and gloss retention. It is ready to brush, roll, or spray without adding and mixing additional components. With VOC content of 250 g/l, low odor formulation is recommended for water tanks, power plants, amusement parks, bridge and highway construction, and for corporate logos and petrochemical plants.

Elscint Automation    Pune 411026  India
May 27, 2005 Sprayable ElscintPUL, used with stainless steel, mild steel, or cast aluminum bowls, can be formulated to provide smooth or rough texture. Smooth formulation reduces noise level by eliminating metal to metal contact, and rough formulation increases friction for oily components to reduce friction between components and bowl track. Offered in thicknesses from 0.40–2 mm and above, green polyurethane lining is US FDA approved.

Chemline Inc.    St. Louis, MO 63103
Jan 24, 2005 Chemical-resistant Chemthane 3300 adds smooth, glossy finish to steel, iron, galvanizing, aged fiberglass, concrete, masonry, and wood substrates. Formulated in 1:3 mix ratio with pigmented acrylic enamel and polyisocyanate hardener, low-VOC coating can be applied by brush, roller, or single component airless pump. It is offered in various colors and exhibits resistance to acids, alkalis, humidity, and salts found in industrial applications.

Chemline Inc.    St. Louis, MO 63103
Oct 22, 2004 CHEMTHANE 2240PW 100% solids coating, engineered for lining potable water tank and pipe applications, can be spray-applied in one coat directly to prepared steel, iron, or concrete substrate. Solvent-free product will not transfer taste or odor into water. Suited for immersion service, aromatic polyurethane allows applicators to achieve film build of 15–70+ mil in one pass. Product also features a cure-to-touch time of 6–8 min.

Sherwin-Williams Co.    Cleveland, OH 44115
Apr 21, 2004 Dual-component Polysiloxane XLE combines properties of epoxy and polyurethane in one coat. Glossy, self-priming coating is VOC-compliant and isocyanate-free and dries in 1 hr to corrosion-resistant finish. Suited for application by brush, roller, and conventional or airless spray equipment, product may be applied directly to properly prepared steel or over inorganic, zinc-rich primers. It is suited for structural steel, tank exteriors, and piping.

Chemline Inc.    St. Louis, MO 63103
Mar 26, 2004 CHEMTHANE 2260â„¢ solvent-free, 2-component polyurethane coating is applied directly to prepared steel, ductile iron, or concrete to provide corrosion protection for substrate. This 100% solids (Zero VOC) polyurethane, used to protect underground tanks, pipelines and pilings, cures to form hard polymer film that demonstrates resistance to adhesion, abrasion, and chemicals. It achieves high film build in single coat multi-pass applications.

Chemline Inc.    St. Louis, MO 63103
Jan 15, 2004 EURO-SEAL 7000 polyurethane encapsulant, suited for use on carved architectural EPS and polyurethane foam elements, provides protection from thermal expansion and UV degradation and strengthens mechanical impact resistance. Able to dry to touch within 10 sec, 2-component, spray-applied polyurethane coating forms hard, chemical-, moisture-, and fire-retardant encapsulation. It enables fabricators to coat foam parts in production-line fashion.

Garon Products, Inc.    Wall, NJ 07719 1924
Aug 22, 2003 Tigerdeckâ„¢ flexible, watertight, polyurethane coating systems protect high traffic concrete, wood, and metal substrates that require chemical resistance. Since multi-layer systems are flexible, they allow substrate to move with changes in temperature and humidity without cracking or popping off. Elastomeric, seamless membrane prevents moisture attack that causes costly damage to any slab. Coatings have low odor and are easy to apply.

Volatile Free, Inc.    Brookfield, WI 53045
Jul 23, 2003 Seamless, elastomeric containment lining, VFI 210®, is spray-applied, bridging hairline cracks in concrete containment areas. Hybrid polyurethane/polyurea system cures instantly to resist moisture in substrate or high humidity from slowing application time. Zero VOC, 100% solids coating is applied with high film builds, has tensile strength ranging from 3,600 psi, and hardness ranging from 95A/57D.

Sherwin-Williams Co.    Cleveland, OH 44115
Jul 16, 2003 Part of ControlTechâ„¢ coatings line, EnviroLastic® AR 520 PW is USDA-acceptable and NSF-approved to ANSI-NSF 61 Standard for potable water storage. Available in brush and caulk grades, impact-resistant, VOC-free, odorless coating dries tack-free in as little as 45 sec. It may be applied at temperatures down to -20°F as well as in high humidity, and is suited for primary and secondary containment applications.

Rez-Solutions    Lakewood, NJ 08701
Nov 26, 2002 Based on pure polyurea, Tough-Cote URC, Tough-Cote URM, and Tough-Cote URR are seamless, flexible coatings that offer water- and chemical-resistance. Products are 100% solids, 2-component, pure polyurea elastomers, and can be applied at temperatures from –40 to +350°F. Coatings, formulated with UV stabilizers, can be applied to metal and roofing substrates, including concrete, foam, and wood.

Sherwin-Williams Co.    Cleveland, OH 44115
Nov 22, 2002 High-build, fast-drying, direct-to-metal Fast Cladâ„¢ DTM Urethane can be applied at 6–9 mils DFT in single coat with no outgassing or pinholing. Urethane dries in 1 hour as corrosion-resistant finish and may be applied at temperatures as low as 35°F, with airless spray equipment, brush, or roller. Coating has 2-hour potlife at 77°F and is for use directly over properly prepared steel.

Garon Products, Inc.    Wall, NJ 07719 1924
Aug 29, 2002 Tigerdeckâ„¢ coating system protects high traffic concrete, wood, and metal substrates that need flexible, chemical resistant coating. Since coating is flexible, it allows substrate to move with changes in temperature and humidity without cracking or popping off. Elastomeric, seamless waterproof membrane prevents moisture attack that causes damage to any slab. Coating has low odor and comes in large selection of colors.

DuPont High Performance Coatings    Wilmington, DE 19898
Aug 12, 2002 Imron® Waterborne Polyurethane Copolymer coatings includes primers, satin-gloss DTM (direct-to-metal), high-gloss topcoats, and flat clear topcoat. Single-component coatings are free of Hazardous Air Pollutants and low in VOC with less than 1.8 lbs/gal. They reach hard dry in 2 hrs and can be re-coated in 30 min. Products can be applied to steel, aluminum, galvanized steel, concrete, fiberglass, and certain plastics.

Sherwin-Williams Co.    Cleveland, OH 44115
Jul 01, 2002 ExpressTechâ„¢ coatings provide fast throughput, fast return to service, fast stack times in fabrication shops, and lower VOC emissions. Fast Clad Zinc inorganically reinforced primer can be recoated in 2 to 3 hr. Reinforced film resists topcoat bubbling, dry spray and mudcracking. FasTop Urethane floor system offers a 6-8 hr return to service. Envirolastic Polyurea can be returned to service in mere minutes, significantly reducing downtime.

Sherwin-Williams Co.    Cleveland, OH 44115
Jun 24, 2002 SHERTHANEâ„¢ 2K URETHANE 2-component, aliphatic acrylic modified, urethane enamel is chemical and abrasion resistant and VOC compliant. It cures to durable, high-gloss, weather-resistant finish, providing long-term substrate protection. Coating may be applied to properly primed steel, galvanized metal, aluminum, and concrete. It is suitable for use in USDA inspected facilities.

General Polymers    Cincinnati, OH 45242
Jun 17, 2002 Water-based FasTopâ„¢ seamless urethane cements can be installed and ready for service in hours because of their Urethane-cement chemical reaction. FasTop M, applied as mortar, can be installed in one step without topcoat. FasTop S System consists of trowled slurry blend with silica sand broadcast finish. FasTop S-U1 Upgrade System uses decorative quartz broadcast instead of silica sand and requires clear topcoat.

Garon Products, Inc.    Wall, NJ 07719 1924
Mar 13, 2002 Concord(TM) polyurethane high gloss enamel resists mild acid and alkali fumes, oil, grease, gases, steam, dirt and abrasion. It is USDA approved for surfaces where there is possible food contact in facilities operating under Federal Meat and Poultry Products Inspection Program. Coating rolls or brushes on and dries to hard, crystal-clear or color finish that is easy to clean and maintain. It seals and coats traffic areas and protects against yellowing.

Aremco Products, Inc.    Valley Cottage, NY 10989
Jan 11, 2002 Corr-Paintâ„¢ coatings are designed for use from 200° to 2500° F. CP20XX Series epoxy and urethane based coatings produce corrosion and wear resistant barriers to 500°F. CP30XX inorganic-ceramic, aqueous-based coatings resist thermal shock and oxidation to 1500°F. CP40XX silicone-based coatings are formulated using VOC-compliant, water-dispersible silicon resin. CP5000 2-part, water-based, inorganic, zinc-rich primer resists immersion, impact, and abrasion.