Low-odor, non-corrosive, non-flammable, and sensor-safe Permatex® Ultra Synthetic RTV Gasket Maker resists chemical properties and prevents leak paths in vehicles with synthetic motor oils. Used as formed-in-place gasket maker or sealant, product provides adhesion and flexibility while maintaining reliable silicone rubber seal. Cured flexible seal, which will not harden, shrink, or crack, exhibits temperature resistance up to 500°F and resists aging, weathering, and thermal cycling.
Manufactured from mineral graphite, EQFG Flexible Graphite Sheet is compressible and conformable, making it suited for gasketing and fluid sealing applications. Product offers chemical resistance and works well to temperatures up to 900°F. Available in 2 sheet sizes of 19 x 19 in. and meter x meter, as well as thicknesses of 1/32, 1/16, and 1/8 in., graphite sheet is also suitable for EMI shielding and gasketing, heat dissipation, lubrication, stress sensing, and vibration damping. Read More
Formulated by combining high-temperature resin with ceramic fibers and powders, Pyro-Putty™ 950 can be used as gasketing compound for boilers, compressors, heat exchangers, furnaces, ovens, and exhaust manifolds. Product repairs rough, scored, or irregular surfaces and is resistant to chemical and steam attack, high pressure/vacuum atmospheres, mechanical vibration, and joint movement. Offered in 11 oz caulk gun cartridge, sealant can cure in service or by heating joint without pressure. Read More
Used as alternative to tapes, PSA die-cut gaskets, 2K epoxies, silicone rope, or RTV sealants, GA-201 seals heat-sensitive substrates such as plastic enclosures. Moisture- and chemical-resistant FIP/CIP gasket acts as barrier to prevent absorption or penetration of air, dust, dirt, noise, liquids, or gaseous substances. Cured by UV/Visible light, tack-free product can be dispensed into intricate or complex configurations and can accommodate design changes. Read More
Provided in 0.125 in. and 0.250 in. thicknesses, Combination EMI Shielding Gaskets are fabricated from closed cell silicone sponge, silicone foam, and fluorosilicone sponge with edge bonded knitted monel wires. Gaskets are thicker and softer than filled conductive rubber EMI gaskets, making them suited for large enclosures requiring environmental gaskets and EMI shielding. Pressure sensitive adhesive aids installation, while monel mesh offers corrosion resistance and ability to resist oxidation. Read More
Combining soft closed-cell silicone sponge core with conductive silver/aluminum in silicone jacket, Ultra-Vanshield® Dual Elastomer EMI/RFI Shielding Gaskets are listed by UL to achieve flame retardancy of UL94V0 under file number E311158. Gaskets are suitable for sealing around fragile components such as high-speed connectors and circuit boards, and are formulated for low compression set and high temperature resistance. Read More
Die-cut thermal interface gaskets transfer heat from electronic components to surrounding environment. When placed between heat source and heatsink, products conform to all uneven surfaces and fill any air gaps. There are 12+ Sarcon® thermal interface material formulations available, and physical characteristics also allow use as low-pressure mounting cushion to prevent deformation. Thermal conductivity ranges from 0.9–17.0 W/m°K with thermal resistance from 0.03–3.47°C in.²/W.
Ultra Grey® Rigid High-Torque, Ultra Black® Maximum Oil Resistance, Ultra Copper® Maximum Temperature, and Ultra Blue® Multipurpose RTV Silicone Gasket Maker products come in tubes that facilitate even and consistent application while also helping to extend product shelf life. Designed to hang directly from peg, tubes also eliminate need for blister card and thereby minimize space requirements within planogram. Screw-on cap also allows upright storage on shelf.
Supporting trend of powertrain modules with lightweight design, Curve Gasket helps minimize amount of structural plastic required in engine covers. To achieve dimensional stability and lower reaction forces essential for sealing lightweight thermoplastic covers, Curve Gasket uses combination of constant and undulated cross-sections that minimize loading. Undulated sections use same design principle as corrugated waves used to stabilize metal sheeting. Read More
Co-dispensed with both conductive and non-conductive material, Trishield Soft® is applied in triangular and wave-shaped gasket. Precise string of electrically conductive silicone rubber is dispensed on carrier and is then formed into characteristic shape. Materials applied include silicone nickel, nickel graphite, and soft nickel graphite. Offered in gasket heights of 1.2–2.5 mm, Trishield Soft comes in range of metal fillers including Ni/C, Ag/Ni, or Ni/Al. Read More
Fingerstock product, Edge Guide Clip-on Strip, offers optimal grounding/shielding contact from PCB to card guide on rack or housing inside electronics. Snap-in feature of contact fingers prevents any potential snagging, allowing for bidirectional sliding contact along edges. Strip, made from BeCu, is available with various plating options, including tin or nickel. While compression forces facilitate card installation, customizable length options afford flexibility in design phase. Read More
UV/Vis, light-curable, Form-In-Place and Cure-In-Place gasketing resins are formulated with high-visibility black (GA-140-B) and green (GA-140-G) color. Bonding to metals, glass, and plastics, products are resistant to high-temperature and high-moisture environments while maintaining adhesion and flexibility. Shrinkage value reduces stress, while in-line curing allows for increased production speed. Chemical- and moisture-resistant gaskets are formulated to be tack free and flexible. Read More
Intended for use by service technicians, mechanics, or repair facilities that have to carry out repairs to machinery which use hydraulic or pneumatic systems, metric O-Ring Kits comprise 300+ individual 70 durometer Buna N O-Rings. Available O-rings range in sizes from 7 mm OD with 2 mm section to 52 mm OD with 4 mm section. Read More
Bright blue in its uncured state, GA-140-SC UV/Vis light-curable, Form-In-Place (FIP) and Cure-In-Place (CIP) gasket enables automated vision systems and manual operations to confirm placement prior to cure. As product cures with sufficient exposure, color transitions to clear. This See-Cure technology provides visual confirmation that adhesive is fully cured and bond site is secure. Product bonds to metals, glass, and most plastics and is resistant to chemicals and moisture. Read More
Classified as Type 4 FKMs by ASTM standards, AFLAS® 200 P is suited for applications that need to withstand aggressive oils containing anti-oxidants, solvents, ozone, acids, and bases. Peroxide-curable product offers optimized performance at cold temperatures (Tg = -13°C, TR-10 = -8°C), and can be solvated and applied as coating. Typical applications include oil seals, shaft seals, O-rings, and variety of other parts and fittings. Read More
Consisting 10 and 20 durometer Shore A molded Liquid Silicone Rubber compounds, respectively, Wacker Silicones LR3003/10TR and LR3003/20TR provide water sealing and protection for enclosures and portable devices. Products feature optimized tear resistance and surface condition as well as resistance to damaging effects of UV. Also available in 10 and 20 durometer, 12 x 12 in. injection molded liquid silicone rubber sheets come in standard thicknesses of .032, .050, .062, .093, and .125 in. Read More
WA, WC, and WP Series, available in sizes from 2.28 x 2.52 in. to 14.12 x 7.84 in. for indoor and outdoor applications, feature silicone rubber gasket and stainless steel screws that protect electronics from harsh environmental factors such as dust, dirt, and moisture. Molded in flame retardant UV-stabilized Polycarbonate plastic, WC and WP Series are conducive to temperatures from -40 to +120°C. WA Series, molded in flame retardant dark gray ABS plastic, suits indoor use from 0 to +80°C. Read More
Intended for fuel cell sealing applications, Ultra Light-Weld® GA-145 UV/Visible light-curable Form-In-Place (FIP) and Cure-In-Place (CIP) gasket is formulated to be tack free, soft, and flexible with low outgassing after cure. Chemical-resistant product, which can be dispensed in intricate and complex configurations, supports in-line curing and bonds to metals, glass, and PC. Gasket cures on demand and exhibits resistance to high-temperature and high-moisture environments. Read More
Offering 1-step solution, Series TTG SpeedFlex® Track Top Gasket provides fire, smoke, and acoustical ratings for head-of-wall joints between gypsum walls and flat concrete floor slabs. Because it is installed at same time as top track, intumescent firestop cover eliminates caulking process and need for second inspection. Gasket is UL classified up to 2 hours, provides acoustical values up to 56 STC in rated and non-rated wall construction, and has received L-rating of less than 1 cfm/Lin. Read More
With digital dieless cutting, EMI/RFI Gaskets and Seals are manufactured to OEM specifications from materials best suited for application, taking into account factors such as flexibility, heat, and resistance to impacts, solvents, and UV. Products can be produced from solid, sponge, and fabric reinforced materials in virtually any shape and size from 0.250–60 in. dia with thicknesses from 0.003 in. Available with or without pressure-sensitive adhesives, parts provide attenuation up to 120 db. Read More