Tube / Pipe / Hose Cutters and Cutting Machinery

Hand-Powered Refacing Tool refaces flange surfaces on 1-4 in. pipes.
Tube / Pipe / Hose Cutters and Cutting Machinery

Hand-Powered Refacing Tool refaces flange surfaces on 1-4 in. pipes.

Suited for use on hard-to-reach pipe flanges whose integrity must be maintained, QuickFace has self-centering design with adjustable collets and clamps that provides concentric operation and accuracy. Portable tool weighs 15 lb and uses ½ in. cutting tools. Interchangeable lead screws make it suitable for resurfacing damaged raised-face and lens-ring joint flanges to varying finish standards....

Read More »
Multi Material Cutter delivers 600 lb of cutting force.
Tube / Pipe / Hose Cutters and Cutting Machinery

Multi Material Cutter delivers 600 lb of cutting force.

Microprocessor-controlled MMC200 cuts round or flat material up to 3.94 in. wide and 5/8 in. thick and can be programmed to cut any length (in. or mm), with 1% or better tolerance. It is also programmable for up to 99 batches and 10 fixed feed rates. MMC200 is rated to cut up to 7,592, 2-in. pieces/hr through makerials such as copper wire and cable, silver solder, power cords, cellophane,...

Read More »
Welding End Prep Tool Fits between Small Boiler Tubes
Tube / Pipe / Hose Cutters and Cutting Machinery

Welding End Prep Tool Fits between Small Boiler Tubes

An air-powered, right angle welding end prep tool that is designed for stainless steel tubes and others with a high percentage of chrome and fits a Dutchman" is available from ESCO Tool of Medfield, Massachusetts. The Esco "Ground" MILLHOG® is a right angle drive I.D. clamping welding end prep tool for water wall boiler tube panels from Â-½" I.D. to 2¼" O.D. by ½" thick...

Read More »
CMAA Crane Buyer's Guide
Sponsored

CMAA Crane Buyer's Guide

CMAA has organized this Buyer's Guide to promote standardization and to assist prospective buyer's of electric overhead traveling cranes in selection of equipment most suitable for their applications.

Read More »
Tube and Pipe Cutter features 2 3/8 in. OD capacity.
Tube / Pipe / Hose Cutters and Cutting Machinery

Tube and Pipe Cutter features 2 3/8 in. OD capacity.

Equipped with ratcheting mechanism, Model RC-2375 minimizes amount of force needed to cut through plastic pipe and tubing. Aluminum construction and ergonomic handles provide comfortable grip for cutting PVC and CPVC, PEX, polyethylene, polybutylene, and rubber hose. With X-CEL(TM) quick-change technology, blade can be changed without tools and lasts up to 2,000 cuts. Ergonomic grips built into...

Read More »
Cutter and Reamers handle stainless steel applications.
Tube / Pipe / Hose Cutters and Cutting Machinery

Cutter and Reamers handle stainless steel applications.

Though specifically designed for use on stainless steel, Model 35S Tubing Cutter cuts copper, steel, and aluminum tubing. It features ergonomic X-CEL knob and roller bearings that minimize friction while optimizing cutting speed. Constructed of hardened steel, Models 227S and 223S inner-outer reamers include integrated measurement tools. Model 227S features 45 cutting edges to allow for inner...

Read More »
Plastic Tubing Cutter provides 1/2-1 5/8 in. OD capacity.
Tube / Pipe / Hose Cutters and Cutting Machinery

Plastic Tubing Cutter provides 1/2-1 5/8 in. OD capacity.

Equipped with ratcheting mechanism, Model RC-1625 cuts plastic pipe and tubing such as PVC and CPVC, as well as PEX, polyethylene, polybutylene, and rubber hose. Quick-change blade pin enables users to change blades by hand in seconds, while assuring there will be no lost clips or screws. Constructed of lightweight aluminum, RC-1625 has ergonomic handles for comfortable grip and thumb latch that...

Read More »
Tube / Pipe / Hose Cutters and Cutting Machinery

Rotary Fly-Knife Cutter

The Rotary Fly-Knife Cutter is an inline (part of an extrusion line) or offline (standalone unit) cutting unit that executes clean (chipless) accurate cuts on various post-extruded plastic and rubber profiles and tubes, such as automotive gaskets, rigid PVC irrigation tubing, and custom profiles. This unit belongs to CDS's family of "Fly-knife Cutters," which employ a fly-knife wheel...

Read More »
5301PD Power Drive
Tube / Pipe / Hose Cutters and Cutting Machinery

5301PD Power Drive

Reed's 5301PD Power Drive rotates the pipe while cutting, threading, or reaming operations are performed on up to 2 diameter pipe and conduit. Reed offers both a basic 5301PD machine with foot pedal and the 5301PD Complete including a tripod, transporter, oiler, carriage, reamer, pipe cutter, universal die head, universal dies, and cutting oil. WHY REED? Flat top of housing is ideal for placing...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers