Transceivers

SFP+ Compliant Transceiver integrates 10 GbE LAN/WAN PHY.

Supplied in 13 x 13 mm package, VSC8486-11 features synchronous Ethernet clocking and delivers high-speed signals for XFP and SFP+ module-based Carrier Ethernet equipment supporting 10 GbE, 10G Fibre Channel, and WIS network applications. Transceiver operates from single 1.2 V supply, and FlexEQ(TM) architecture features circuitry that compensates for connector and channel losses. Typical power...

Read More »

Wireless MODBUS(TM) Gateway

THE WOODLANDS, TX - Detcon's Model RXT-300 is a new wireless mesh-network transceiver designed to transmit signal data in a wide range of industrial applications. The transceiver operates at a universally acceptable frequency of 2.4GHz. Model RXT-300 uses direct sequence spread spectrum wireless mesh technology. Processing power is shared among transceivers allowing each one to act as both a...

Read More »

PCIe 2.0 Gen 1 UARTs offer up to 25 Mbps serial data rate.

Featuring PCIe 2.0 Gen 1-compliant bus interface, XR17V352/354/358 are 2-, 4-, and 8-channel UARTs, respectively, that support FIFO sizes up to 256 bytes. Single-chip endpoint solution eliminates requirement for external PCIe-PCI bridge devices. It integrates on-chip PCIe PHY and PCIe digital controller as well as RS-485 half duplex direction control with programmable turn around delay; infrared...

Read More »
Transceiver is certified to FlexRay(TM) Standard v2.1 Rev B.

Transceiver is certified to FlexRay(TM) Standard v2.1 Rev B.

Acting as interface between digital logic and copper cable transmission in automotive networks, AS8221 FlexRay Standard Transceiver is capable of transmission rates up to 10 Mbit/sec. RoHS-compliant unit provides all functions to enable integration in electronic control units powered with permanent battery voltage. While microchip is only fed by car battery, it provides wake-up functionality via...

Read More »
Considerations for Choosing a Plastic Injection Molder
Sponsored

Considerations for Choosing a Plastic Injection Molder

Choosing a plastic injection molder is no small decision. There are a number of factors that play into your selection, and it's important to consider them all to ensure you find the plastic injection molding company that suits your unique needs. This eBook is your guide to identifying those factors to help you make an informed decision.

Read More »

EPON Transceiver has integrated clock and data recovery.

Single-chip 10G EPON transceiver for next generation PON systems, GN7350 enables users to build prototype systems for in-house and field testing. CDR eliminates excessive channel noise, and ensures highest link margin and lowest jitter signal by re-timing high speed signal. Custom 10G burst mode transceiver helps reduce BOM.

Read More »

UHF Devices extend range of wireless car access systems.

Supplied in 32-pin, 5 x 5 mm QFN package, sub-1 GHz CC11x1-Q1 Series transmitters, receivers, and transceivers have RF design and SPI that eliminate need for external filters or switches. Devices allow migration from unidirectional to bidirectional systems and support operation up to +125-

Read More »

Transceiver Module offers extended 802.15.4/ZigBee range.

With range of up to 2 miles, MeshConnect(TM) Extended Range Module (ZICM2410P2) enables LED lighting control and applications in RF-noisy environments. Solution integrates built-in voice CODEC processor, while +123.5 dB link budget enables optimal data rates to be maintained for extended distances. Intended for 802.15.4/ZigBee applications, product consumes less than 1 -µA during sleep mode...

Read More »

Full-Duplex IF Transceiver offers optimized integration.

Supplied in 14 x 14 mm QFP, TRF2443 low-noise intermediate frequency (IF) transceiver features cross-polarization interference cancellation support. Integration of 15+ functional blocks, along with output third order intercept point of 29.5 dBm and receiver noise figure of 4.3 dB, ensures linearity and sensitivity suited for wireless infrastructure backhaul and point-to-point microwave end...

Read More »
RF Transceiver has dual receivers to minimize channel fading.

RF Transceiver has dual receivers to minimize channel fading.

MAX2839AS WiMAX(TM) MIMO RF transceiver includes two 2.3-2.7 GHz receivers that feature 2.3 dB noise, -81 dBm sensitivity for 64 QAM signal at 5 MHz channel bandwidth, and 95 dB gain control range digitally controlled in 1 dB steps. Transmitter has 62 dB gain control range controlled in 1 dB steps, 0 dBm linear output with 64-QAM signal, and greater than -45 dBc of sideband suppression. Contained...

Read More »

HDMI 1.4 Transceiver reduces A/V design complexity.

In addition to supporting features such as on-screen display and audio-return channel, ADV7623 integrates 4:1 multiplexed input HDMI receiver, HDMI transmitter, as well as CEC (Consumer Electronics Control) buffer and controller into one single-chip platform. Xpressview(TM) technology enables seamless, automatic switching between HDMI-enabled AV devices in a fraction of one second, eliminating up...

Read More »

All Topics