Electronic Drivers

Power MOSFET Driver operates reliably from -55 to +225°C.
Electronic Drivers

Power MOSFET Driver operates reliably from -55 to +225°C.

Suited for driving MOSFETs in DC-DC converters and electric motor control applications, HYPERION features typical on-resistance of 1 W. High- and low-side unit can drive up to 1 nF loads with 40 nsec propagation delay and 15 nsec transition time at 200°C. Adaptive non-overlap circuitry reduces switching losses by preventing simultaneous conduction when used in MOSFET drive applications....

Read More »
Electronic Drivers

Gate Drive Interface Board is designed for dual IGBT modules.

Model VLA536-01R is gate drive interface board in which control signals are isolated using high-speed optocouplers with 15 kV/Â-µs common mode noise immunity. It provides 2,500 Vrms isolation for control power and signals, as well as isolated fault feedback signal if short circuit condition is detected. Measuring 101 x 64 mm, board includes CMOS-compatible input interface and mounts to dual...

Read More »
Electronic Drivers

MOSFET Driver powers white LED backlighting.

Suited for LCD panel backlight applications such as car navigation monitors and 12 in. notebook PCs, 60 V Model SSM3K318T boosts battery voltage to level needed to turn on LED array. N-channel power MOSFET features low ON-resistance of 83.5 mW at V(GS) = 10 V and low capacitance of 235 pF at V(DS) = 30 V. Device is available in TSM package measuring 2.9 x 2.8 x 0.7 mm.

Read More »
DC/DC Converter drives high-current LEDs.
Electronic Drivers

DC/DC Converter drives high-current LEDs.

Featuring 3-40 V input voltage range, LT3519, 45 V current sense DC/DC converter drives up to ten 100 mA white LEDs from 12 V input. It senses output current at high side of LED, enabling buck, buck-boost, or boost configurations. True Color PWM(TM) dimming delivers constant LED color with ranges of more than 3,000:1. Providing open LED protection, soft-start, and thermal protection, it is...

Read More »
Multi-channel LED Driver has 3,000:1 True Color PWM dimming.
Electronic Drivers

Multi-channel LED Driver has 3,000:1 True Color PWM dimming.

Supplied in 32-pin, 5 x 5 mm QFN package, LT3754 can drive 16 channels - each with up to ten 50 mA white LEDs in series - from 12 V input while delivering efficiencies exceeding 92%. IC operates from 6-40 V input; utilizes step-up DC/DC controller; and offers features such as ±2.8% (±0.7% typ) LED current matching, programmable 100 kHz to 1 MHz fixed frequency operation, and current...

Read More »
Electronic Drivers

High-Voltage Driver integrates IO-Link, DC/DC converter.

Supplied in 4 x 4 mm QFN24 package with exposed die paddle that ensures optimal heat distribution, ZIOL2401 offers 2 independent IO channels that meet physical layer requirements of sensor and actuator systems in factory automation applications. IC operates over -25 to +85°C range and combines fully programmable, 2-channel IO-Link driver with DC-DC converter capable of producing up to 15 V....

Read More »
White LED Driver features display backlight control.
Electronic Drivers

White LED Driver features display backlight control.

Offered in 12-bump micro SMD package measuring 1.615 Ã-— 1.215 × 0.425 mm, LM3530 can be utilized for illuminating larger displays in portable media devices. Current-mode boost converter can supply up to 29.5 mA of power to 11 white LEDs from single-cell Lithium-Ion battery. I2C compatible interface offers programmability, and enables designer to adjust for lighting effects such as...

Read More »
Development Kits enable evaluation of OEM LED-backlit LCDs.
Electronic Drivers

Development Kits enable evaluation of OEM LED-backlit LCDs.

Providing everything needed to get panel, backlight, and driver fully operational, Smart Kit(TM) Development Kits include ERG LED driver card, flying lead input harness, DigitalView® to ERG plug-and-play input harness, and direct mate LED driver-to-LCD interconnect wiring harness. All components come in 8.5 x 5 in. polyethylene bag labeled with manufacturer and model number of LCD panel as...

Read More »
Electronic Drivers

Dual White-LED Flash Driver optimizes picture quality.

Integrating 2 MHz synchronous boost converter, 500 mA programmable current source, and I2C interface, inductor-based Model ADP1655 maximizes limited current available in battery-operated digital cameras to increase flash brightness to over 200 Lumens. Transmit masking function allows cell phone camera flash to run at higher LED current while simultaneously operating phone's RF transceiver....

Read More »
Quad-Output EL Lamp Driver incorporates I²C interface.
Electronic Drivers

Quad-Output EL Lamp Driver incorporates I²C interface.

Supplied in 4 x 4 mm TQFN package, MAX14521E features ±15 kV ESD protection and utilizes inductor-based boost converter to generate 300 VP-P (max) voltage for optimal electroluminescent (EL) lamp brightness. IÂ-²C interface is included for adjusting settings such as output voltage, frequency, boost frequency, and waveform shape, while acoustic-noise-reduction circuit enables quiet EL...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers