Electronic Drivers

Electronic Drivers

Camera Flash LED Driver delivers up to 1.2 A.

Integrating 1.2 A boost converter and LED driver circuit into 1.3 x 1.3 mm chip scale package, Models MIC2873/MIC2874 operate from 2.7–5.5 V and feature up to 92% efficiency. High switching frequencies of 2 MHz for MIC2873 and 4 MHz for MIC2874 allow use of miniature size chip inductor and small input/output capacitors. Operating in either flash or torch mode, devices can provide boost or...

Read More »
LED Power Supplies are available with optional dimming.
Electronic Drivers

LED Power Supplies are available with optional dimming.

Used for indoor and outdoor, LED-based lighting and moving sign applications, LDP Series includes LED drivers offering 24, 36, and 48 V constant current outputs over range of 25, 40, and 60 W. Optional dimming function is available via signal from dimming controller with PWM/1–10 Vdc control signal. Along with universal 90–305 Vac input range, features include >0.9 active PFC and

Read More »
Pick and Hold PWM Modules are adjustable and reprogrammable.
Electronic Drivers

Pick and Hold PWM Modules are adjustable and reprogrammable.

Based on MCU that can be reprogrammed for application, 3.00- x 3.00 x .85 in. PH-ET Pick and Hold modules operate on single supply from +9 to +50 Vdc and are suited for driving solenoids, valves, relays, actuators, DC motors, hydraulics, electromagnets, and LEDs. Holding current is 4 A RMS with peak (Pick) current of 15 A for high force/acceleration. Higher current and voltages...

Read More »
Electronic Drivers

N-FET Pre-Driver IC suits automotive DC motor applications.

Offered in 28-pin package with 4 digital inputs, Model MLX83100 can simultaneously drive four 500 nC-rated N-FETS at up to 28 V operating voltage with minimal self-heating. Device supports 45 V automotive load dump conditions and 100% pulse width modulated operation. Integrated bootstrap function and charge pump allow for support of supply voltages down to 4.5 V, ensuring continuous operation...

Read More »
Motor Pre-Driver IC targets automotive safety applications.
Electronic Drivers

Motor Pre-Driver IC targets automotive safety applications.

Compliant with ASIL D, Model TB9052FNG is suited for safety-critical automotive applications such as electric power steering. Unit features built-in motor current detection circuit in redundant configuration as well as range of circuits that detect system failures, including battery under-voltage, over temperature, and driver electrical short. Housed in 12.5 x 6.1 x 1.2 mm package, IC has 2...

Read More »
High Wattage LED Drivers readily accept DC or AC input.
Electronic Drivers

High Wattage LED Drivers readily accept DC or AC input.

Comprising 120, 150, and 200 W drivers, PLEDDC series accept universal 100–277 Vac or 108–250 Vdc input without any modification and provide flicker-free output. Constant-current, dimming, and constant-voltage versions are available.- Able to be used in dry and damp locations, IP66-rated products also feature Black Magic Thermal Advantage™ aluminum enclosures.

Read More »
LED Light Engine suits exterior applications.
Electronic Drivers

LED Light Engine suits exterior applications.

Featuring IP65 rating with LED chamber and optics sealed, AVISTA LED Light Engine uses just 41 or 57 W and directs symmetrical or asymmetrical light precisely where it is needed. Unit is designed to maximize light output on ground or other surfaces with exact center beam candle power. Constructed with anodized aluminum heat sink, light engine is available in 3,000, 4,000, and 5,000 K CCTs, suited...

Read More »
Electronic Drivers

Constant Current LED Drivers suit low-wattage lighting systems.

Offering up to 86% efficiency, LCM-25 and LCM-25DA 25 W LED power supplies let designers implement low-wattage intelligent LED lighting control systems and project style lighting designs. Output can be set to levels from 350 mA to over 1 A via built-in DIP switch. While LCM-25 features- 2-in-1 dimming function that can be driven by 0–10 Vdc or by PWM control inputs, digital LCM-25DA is...

Read More »
Electronic Drivers

Future Electronics Promotes Micrel's MAQ412x Series Dual Low-Side MOSFET Drivers

Pointe Claire, Quebec- – Future Electronics, a global leading distributor of electronic components, announces immediate availability of the MAQ412x Series of dual low-side MOSFET drivers from Micrel. The MAQ4123/MAQ4124/MAQ4125 are a family of dual 3A buffer/MOSFET drivers intended for driving power MOSFETs, IGBTs and other heavy loads (capacitive, resistive, or inductive) which require low...

Read More »
Electronic Drivers

LCoS Module targets head-mounted displays.

Featuring liquid crystal on silicon technology, Front-Lit™ LCoS Module integrates LED illumination system and polarization beam splitter, cutting size and optimizing power efficiency of entire optical engine. Module produces over 10,000 nits of brightness and more than 50 nits/mW efficiency. Meeting specifications of head-mounted display requirements, device targets augmented reality and...

Read More »
Precision Machining Solutions with Over 25 Years of Experience
Sponsored

Precision Machining Solutions with Over 25 Years of Experience

Quality, customer service, and unbeatable value are the hallmarks of Hogge Precision. Since 1989 we have built a reputation as the go-to precision machining source, servicing many demanding industries. For CNC machining and screw machining, there are few manufacturers that can match our capabilities and expertise. See our video to learn more.

Read More »

All Topics