Electronic Drivers

LED Driver IC targets automotive interior lighting.
Electronic Drivers

LED Driver IC targets automotive interior lighting.

Providing up to 100 mA from each of 4 outputs, Model A6263 drives arrays of high brightness LEDs with constant current for safe operation. Outputs can be connected in parallel or left unused as required, andÂ- regulated LED current from each output is set by single reference resistor. Housed in 8-pin SOICN package with exposed thermal pad for thermal dissipation, programmable current...

Read More »
Low-Power EML Driver serves next gen CFP/CFP2 applications.
Electronic Drivers

Low-Power EML Driver serves next gen CFP/CFP2 applications.

Supplied in 4 x 4 mm SMT package,Â- MAOM-002203 consumes 0.75 W and offers typical rise and fall time of 12.5 psec. This electro-absorption modulator driver IC for 100G applications is driven with differential input signal that can range from 250–500 mVpp and provides single-ended output that can be controlled from 1.0–2.5 Vpp. Along with 28 Gbps max data rate,...

Read More »
LED Driver IC serves automotive interior lighting applications.
Electronic Drivers

LED Driver IC serves automotive interior lighting applications.

Supplied in 8-pin SOIC package with exposed pad, A6269Â- automotive-qualified, linear, programmable current regulator can drive 2 LED strings at up to 200 mA each. Regulated LED current from each of 2 outputs is set by single reference resistor, outputs can be connected in parallel or left unused as required, and current matching in each string is achieved without ballast resistor....

Read More »
LED Drivers fit T5 fluorescent ballasts.
Electronic Drivers

LED Drivers fit T5 fluorescent ballasts.

Featuring form factor that matches T5 fluorescent ballasts, 35 W LED Drivers can be used in existing fixture designs or new offerings, as well as utilized for LED retrofits in field. IP65-rated units have input voltage range from 120–277 Vac and offer over-voltage, over-current, and short circuit protection with automatic recovery. Drivers are UL Recognized for both U.S. and Canada, and are CE...

Read More »
Constant Voltage LED Power Supply is available with flying leads.
Electronic Drivers

Constant Voltage LED Power Supply is available with flying leads.

Supplied in IP67-rated, fully encapsulated, 8.98 x 2.83 x 1.73 in. enclosure, GLV-24-150 has universal 100–277 Vac input range and output voltage of 24 Vdc at 6.25 A. Specifications include 90% efficiency,Â- 0.95 PFC, 500 mV peak-to-peak noise and ripple, 200 ms rise time, 2% load regulation, and 50 A max cold start inrush current at 220 Vac. Respectively, input current is 1.8 and...

Read More »
Electronic Drivers

Power Management Gate Drivers target IGBT and SiC FET designs.

As 35 V, single-channel output stage power management gate drivers, UCC27531 and UCC27532Â- prevent digital controllers from operating too close to power circuitry. UVLO settings and rail-to-rail output voltage provide system protection, while split-output configuration improves Miller turn-on immunity and prevents IGBT/MOSFET damage. Along with peak current of 2.5 A source and 5 A...

Read More »
Electronic Drivers

LED Driver offers multiple dimming options.

Supplied in QFN-16 package with Pb-free pure-tin plating and flammability rating of UL 94V-0, PA5711 offers such dimming options as PWM, Linear Dimming, Motion Detection, and Light Sense control inputs. Direct gate driver control is available through active high enable pin, and internal oscillator frequency can be set externally through resistor. Allowing leading edge blanking with desired delay...

Read More »
Electronic Drivers

Two-Channel LED Drivers are suited for use with high-CRI lamps.

Providing color control for 2-color LED light engines, MSL2021/23/24 two-channel SSL LED drivers can be accompanied with Atmel AVR® MCU or ARM® processor-based MCU. Each model drives one dominant LED string withÂ- linear controller and one color LED string with low-side buck controller to achieve target CCT coordinate and replicate color spectrum to attain high...

Read More »
Electronic Drivers

LED Controller and Driver facilitate retrofit bulb design.

Offered in 6-pin TSOT package measuring 2.9 x 2.9 mm, Model TPS92075 is designed for phase-dimmable, offline AC/DC LED lamp and downlight applications such as E14, GU10, A19, and PAR20/30/38 bulbs. Constant-current lighting controller achieves power factor correction above 0.9 while delivering flicker-free dimming when used with conventional wall dimmers. Supplied in 10-pin PowerPad™ MSOP...

Read More »
Electronic Drivers

IC Coupler drives middle-capacity IGBT or power MOSFET.

Housed in SO6 package, Model TLP152 consists of GaAlAs infrared LED optically coupled to high-gain photodetector IC chip. Unit achieves low output current of 2.5 A and contributes to low-power consumption with operating power supply voltage of 10–30 V. With guaranteed minimum creepage and clearance distances of 5 mm and internal insulation thickness of 0.4 mm, Model TLP152Â- is suited for...

Read More »

All Topics