Angled D-Sub Pressfit Connectors have modular design.
Pressfit versions with lead-free surface are intended for applications where automated SMT assembly is not possible, subsequent placement of connector is required, or connectors are pre-mounted in housing and board is pressed in. Insertion forces are absorbed by form-fitting contacts in insulating body made of high-temperature resistant thermoplastics, and bolt anchoring ensures stability. They...
Read More »
Finger-Proof Connectors provide user safety.
PowerpoleÃ-® 15/45 Connectors prevent finger access when unmated and energized. Flat-wiping contact system reduces contact resistance at high current, while wiping action cleans contact surface during connection/disconnection. Molded dovetails secure connectors into keyed assemblies, preventing misconnection. With interchangeable genderless design, connectors are rated 15, 30 and 45 A for 600...
Read More »
Backplane Connector suits high-speed systems.
Series Tempus(TM)-HS 4000 features 0.5 mm plated through-hole, resulting in less capacitance, delivering less than 5% crosstalk above 5 Gbyte/s and differential insertion loss under 1 dB at 5 Gbyte/s. The 2 mm connector is drop-in replacement for FCI's HS4000 products. Short signal tuning forks reduce electrical length of overall mating interface. Connector is capable of 10 Gbyte/s signals in...
Read More »
Receptacles are offered in right angle PCB mount.
Attached to brass housings that provide watertight seal, 3-, 4-, and 6-pin M8 picofast receptacles and mating cordsets are suited for power and signal transfers. Male and female PCB receptacles are available; former mates with threaded and snap-lock picofast cordsets, while latter works with picofast threaded cordsets. All versions provide protection that meets IEC IP 67. Voltage and current...
Read More »
Workwear Goes Hand-In-Hand with Employee Satisfaction and Retention
High-quality gear reminds employees that they are valued by their employer and improves their workday. To find out more about choosing the best workwear, download now.
Read More »
Wire Connectors utilize push-in design.
In-Sure(TM) Push-In Wire Connectors fit any combination of 12-18 AWG stranded copper and 12-20 AWG solid conductors. Push-in design terminates conductors without twisting, while clear polycarbonate housing permits visual verification of connection. Units include stainless steel inserts to restrict pullout, electrolytic tin-plated copper bus system, integral test port for voltage and continuity...
Read More »
Cordsets and Receptacles have 0.24 in. diameter.
Providing protection that meets IEC IP67, M5 pentafast threaded connector products offer 3 or 4-pin connection with coupling nut that measures 0.24 in. in diameter. Multi-pin molded cables are available with PUR cable, straight or right angle configurations, standard or custom lengths, as pigtail or extension cords. Rated for 125 V and 1 A, products are suited for power and signals to factory...
Read More »
Plugs/Connectors offer protection of rubber and nylon.
Safeway+ Wiring Devices consist of plugs and connectors with 3-piece Core-Lock(TM) rubberized-nylon assembly, engineered for general-purpose wiring device applications. They lock together with 2 screws, while reversible cord clamp accommodates cords from 12-18 gauge. Nylon core is surrounded by protective rubber coating, providing impact resistance without marring. They are UL/CUL LISTED and come...
Read More »
Interconnects meet high-speed, board stacking requirements.
RISE-UP(TM) Series HSC8 uses controlled impedance PCB with embedded ground plane. Units are capable of transmitting data in excess of 6.25 Gb/sec and operate at up to 3.5 GHz/differential pair in 25 mm board stacking applications. Series HSEC8/MEC8 interfaces allow parallel board stacking, as well as perpendicular daughtercard type applications, and horizontal or coplanar applications....
Read More »
Elastomeric Connectors suit portable and handheld devices.
Gold STAX(TM) zero-insertion-force connectors are composed of alternating layers of conductive and non-conductive silicone rubber. Interconnection is made by deflecting elastomeric connector between mirror image pad patterns on mating substrates. Gold-coated particles embedded within low-durometer silicone create thousands of conductive paths, providing multiple points of contact to substrate...
Read More »
Modular Coaxial Connectors offer 2, 3, or 4 ports.
CoSMID 75 ohm, surface mountable connectors incorporate plastic housing that can be plated and molded into various configurations. They feature 1.0/2.3 coaxial interface to CECC 22230 with typical reflection factor of less than 0.1 up to 500 MHz. Units can be processed through normal reflow soldering processes at temperatures up to 473Ã-
Read More »
Eliminate Expensive Repairs with the Hot-Shot Pipe Thawing Machine
The new Hot Shot Pipe Thawing Machine delivers an innovative and highly effective approach to thawing frozen pipes. Easy to use and versatile, it is loaded with robust features that further suit it to many challenging environments. To learn all about it, see our video.
Read More »
