New Digital Memory Products

High-Density EEPROMs come in tiny, 8-lead MSOP package.

Models 24LC128 and 24LC256 are 128-kbit and 256-kbit I2C(TM) serial EEPROMs, designed in PMOS Electrically Erasable Cell(PEEC) process technology. For low operating voltage requirements, 24LCXX EEPROM family can operate down to 2.5 volts. Units are only 1.1 mm high, making them suitable for cell phones, PC cards or other height-restricted applications.

Memory Card is accessible inside controller.

Removable Memory PMC card option for Emerald EMC-2000 Multi-axis Motion Controller is suitable for loading of EMC-2000 operating system or application program software. SMARTMEDIA card, same type as used in digital cameras, can be programmed with PC then loaded into EMC-2000. PMC card fits inside of Emerald Controller with SMARTMEDIA easily accessible.

Memory Board is VMEbus-compatible.

Fiber-optic VMIVME-5565 Reflective Memory Board allows computers, workstations, PLCs, and other embedded controllers with dissimilar or no operating systems to share data in real-time between up to 256 nodes at rates up to 174 Mbyte/s. It can be configured with 64 Mbyte or 128 Mbyte of on-board SDRAM. Transfer of data between nodes is software transparent, requiring no I/O overhead. Transmit and...

Tiny MSOP Package supports 32 and 64 kbit serial EEPROMS.

With 2.5 V operating voltage, 1 milliamp active current, and 1 microamp standby current, 24LCXX device suits most applications. 24AAXX version enables operation down to 1.8V for battery-powered applications. Eight-lead package is designed with company's PEEC technology; footprint is approximately 14.7 cu mm (including leads), 23% smaller than TSSOP package. At 1.1 mm in height, MSOP is 29% lower...

The Legacy Automation Playbook

How to Proactively Manage Your Legacy Industrial Control System

EEPROM Device is available in RAD-PAK(R) version.

EEPROM 5962-38267 1Mb memory device is included on Standard Microcircuit Drawing (SMD). It is available in 250, 200, 150 and 120ns speeds. Device provides write-cycle endurance of more than 10,000 write/erase cycles in Page Mode and data retention of greater than 10 years. It offers Total Dose Hardness to 100 krad (Si) in RAD-PAK(R) package, which incorporates radiation shielding.

EEPROMs adhere to VESA's E-DID 1.3 Standard.

With 256 x 8-bit dual-mode serial EEPROM, 24LC22A and 24LCS22A implement both DDC1(TM) and DDC2(TM) operating modes, including recovery to DDC1. They offer 2-wire serial interface bus, ESD protection greater than 4000 volts, and operating range of 2.5 to 5.5 V. Model 24LCS22A provides software-enabled hardware write protection pin to write-protect memory contents automatically during in-circuit...

Memory Board offers 64 or 128 Mbyte SDRAM.

VMIPCI-5565 is a 2 Gbaud, fiber-optic, PCI bus-compatible reflective memory board. It allows computers, workstations, PLCs, and other embedded controllers with dissimilar or no operating systems to share data in real-time between up to 256 independent systems at rates up to 174 Mbyte/s. Writes are stored in local SDRAM and broadcast over high-speed fiber-optic data path. Transmit and Receive...

Serial EEPROMs come is 5-lead, SOT-23 package.

Designed in PMOS Electrically Erasable Cell (PEEC) process technology, I2C(TM) Series EEPROMs support all densities through 16-Kbits. With operating voltage down to 2.5V, active current of 1 milliamp, and standby current of 1 microamp, 24LCXXB devices are suitable for many applications. For battery-powered applications with lower voltage requirements, 24AAXX versions enable operation down to 1.8V.

16 Megabit SRAM takes radiation doses to 100 krad.

Model 89C1632 16 Mbit SRAM has access times of 20, 25, or 30 ns, 3V or 5V power supply, equal address and chip enable access times, and 3-state outputs. All inputs and outputs are TTL compatible. It reduces power consumption, and eliminates need for external clocks or timing strobes. Module's 4-Mbit SRAM die and bypass capacitors are incorporated into high-reliability hermetic 68-pin quad...

How SpinSelect Can Save You Time and Money

Thanks to the unique SpinSelect™ Multi-Pocket selectable quick change tool holder, it's time to rethink the range, complexity and volume of parts that your lathe can produce. Our Spin-Select™ tool was created to increase productivity and consistency by decreasing downtime associated with lathe cutting tool and insert setups or changeovers. This product is a game-changer for the industry and we're pleased to show you why.