DC to DC Power Supplies (Converters)

Isolated DC/DC Controller integrates opto drive.
DC to DC Power Supplies (Converters)

Isolated DC/DC Controller integrates opto drive.

Model LT3804 is a 100 W, secondary side, DC/DC regulator for dual output isolated power supplies. Housed in 28-lead TSSOP package, it converts 36-72 V supplies to output voltages of 5, 3.3, 2.5, 1.5, and lower at up to 50 W per output. Differential Kelvin voltage sensing is used for each output feedback. Model LT3804 operates with switching frequencies from 200-800 kHz. It contains error...

Read More »
Quarter Brick DC/DC Converters have 100 W max output.
DC to DC Power Supplies (Converters)

Quarter Brick DC/DC Converters have 100 W max output.

Utilizing integral multiplayer/PCB planar magnetics, QB Series converters offer up to 100 W of output power at currents to 30 A. Available in single outputs from 1.2-7.5 Vdc, products feature input ranges of 18-36 Vdc and 36-75 Vdc. Units offer input under-voltage lockout, output OVP, and over-temperature protection. Hiccup-mode output overload protection supports continuous overload conditions....

Read More »
DC/DC Converter is offered in 6-lead ThinSOT package.
DC to DC Power Supplies (Converters)

DC/DC Converter is offered in 6-lead ThinSOT package.

Combining internal 42 V, 1.1 A VCESAT switch with soft-start capability, LT3467 uses constant frequency current mode architecture and operates from input voltage range of 2.4-16 V. Step-up DC/DC converter employs ceramic capacitors and inductors and 1.3 MHz constant switching frequency for low noise operation. Additional offerings include pin-to-pin compatibility with LT1930 and LT1613 and...

Read More »
DC/DC Converters feature isolated outputs.
DC to DC Power Supplies (Converters)

DC/DC Converters feature isolated outputs.

Series 6E offers 16 high-efficiency 25/30 W Converters with pi input filters and 4:1 input voltage range. Input voltages include 9-36 and 18-72 Vdc. Units are available with single, dual, and triple outputs, which are totally isolated from input. For power conservation, CMOS/TTL compatible Remote On/Off Control allows converters to be powered down. Efficiencies up to 84% are achieved due to 200...

Read More »
DC/DC Converter provides step-up and step-down regulation.
DC to DC Power Supplies (Converters)

DC/DC Converter provides step-up and step-down regulation.

Model LT3433 current-mode DC/DC converter operates from input voltage of 4-60 V, delivering regulated outputs between 3.3-20 V and 200 kHz constant frequency operation. Burst Mode® reduces no-load quiescent current to 100 Â-µA. Converter incorporates dual internal 500 mA switches, which seamlessly switch between step-down and step-up voltage conversion. Programmable soft-start helps...

Read More »
Buck-Boost DC/DC Converter delivers up to 1 A.
DC to DC Power Supplies (Converters)

Buck-Boost DC/DC Converter delivers up to 1 A.

Model LTC3441 synchronous, fixed frequency converter offers efficiencies up to 95%, optimizing battery run time for battery-powered applications. It operates from input voltage of 2.4-5.5 V and can provide up to 1 A at fixed output voltage between 2.4-5.25 V. Buck-Boost topology allows unit to operate above, below, and equal to output voltage with single inductor. Operating frequency is set...

Read More »
DC to DC Power Supplies (Converters)

DC/DC Converter delivers up to 600 mA from 2 channels.

Model LTC3407 1.5 MHz synchronous-buck regulator operates from input voltage of 2.5-5.5 V, using constant-frequency, current-mode architecture. It generates 2 independent output voltages as low as 0.6 V, enabling it to power low-voltage DSPs and microcontrollers. Switching frequency of 1.5 MHz allows utilization of tiny ceramic capacitors and inductors less than 1.2 mm in height. Unit delivers...

Read More »
Synchronous Buck Converter meets CPU requirements.
DC to DC Power Supplies (Converters)

Synchronous Buck Converter meets CPU requirements.

Model FAN53168 multi-phase, DC-to-DC PWM controller and Model FAN53418 synchronous, MOSFET driver work together to form multi-phase synchronous buck converter. To meet tight VRM/VRD10 loadline, FAN53168 uses temperature-compensated inductor current sensing. Unit combines high-speed control loop with active voltage positioning to meet CPU load transient requirements. FAN53168/FAN53418 chipset...

Read More »
Integrated Converter handles output voltages of 0.8-1.2 V.
DC to DC Power Supplies (Converters)

Integrated Converter handles output voltages of 0.8-1.2 V.

FunctionPAK® FX5545G008 consists of one single-package, DC/DC, synchronous buck converter rated for max output power of 3.6 W and max current of 3 A. It delivers power density of more than 380 W/in.Â-³ and comes in 20-port, surface-mount, BGA package that measures 14.7 x 12.2 x 3 mm. Unit converts 2.5-6 V inputs to 0.8-1.2 V output voltage and can shift DC voltage levels while...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers