New Data Acquisition Systems Products

DAQ Boards expand sensor inputs and power options.

Model SB-675 Multirange Signal Adapter Board enables DatastickÃ-® DAS-1245 Data Acquisition System for Palm(TM) handhelds to read measurements across range of input voltages and to supply power to sensors. Model SB-675ZP High-Impedance Board protects DAS-1245 peripheral from voltage surges with high-impedance analog isolation for its 4 analog channels and optical digital isolation for digital...

Monitoring/Control/DAQ System offers self-paced learning.

SNAP Ultimate I/O Learning Center gives users hands-on experience configuring I/O points, reading and writing to those points, writing simple control strategies, and building GUIs. Product includes SNAP Ultimate processor and assorted I/O modules, as well as SNAP rack, power supply, load panel, and cables. Product also comes with software applications and utilities such as ioControl(TM),...

Digital Sensing System measures up to 32 accelerometers.

DSS uses DSIT (Digital Sensor Interface Transmitter) technology to optimize use of digital technology in structural dynamics and modal analysis measurements. Multi-channel, multi-drop, data acquisition system measures up to 64 channels per chassis. Remote DSITs perform 24-bit analog-to-digital conversion near ICPÃ-® accelerometers and transmit signals back digitally via ribbon cable. System...

Data Capture System is Linux based.

Vexcel Data Capture System (VxDCS) incorporates disk array, which may contain up to 10 disk units, into rack mountable chassis. System also houses Vexcel Ion(TM) circuit boards and PC components. Tape drive, for data archiving, is optional. Machine is available in low-end and high-end configurations at respective processing speeds of 200 and 380 Mbps. Product is suited for direct-to-disk data...

Taking a New Product to Market: Outsourcing vs. Internal Product Development

To learn if outsourced new product development (NPD) is right for your needs, and how companies like Vollrath Manufacturing Services can help, download this white paper now.

Data Acquisition Systems are Ethernet-based.

DaqBook/2000E and WaveBook/516E allow user to continuously acquire data to PC at rates up to 1 M readings/sec. Ethernet allows instrumentation to be located up to 300 ft from PC. With over 40 different signal conditioning and expansion options, units are suited for in-vehicle, laboratory, and factory floor applications. Software support includes LabVIEWÃ-® drivers, Visual Basic, C++, DASYLab,...

Data Acquisition Devices delivers input at rates to 800 kS/sec.

NI PXI-6120 and NI PCI-6120 simultaneous sampling, multifunction DAQ devices deliver 16-bit analog input on each of 4 channels for transient measurements and frequency domain measurements. Users can synchronize onboard digital I/O and waveform output with devices' waveform acquisition for mixed signal and stimulus-response applications. Products come with 64 million samples of onboard memory, two...

Data Acquisition System offers multi-channel capabilities.

Model PI-3105 tests analog imaging devices with multiple outputs. It offers programmable gain, filter, strobe timing, and CDS timing on per channel basis, and provides global offset control. All analog components are electronically isolated from digital section ensuring low noise environment. Scalable system offers 1-32 channels of signal conditioning and A/D conversion. Digital data are...

Data Acquisition Module collects all machine events.

Data-Transmission Unit-III (DTU-3) allows DNC plus to collect machine events, automatic and manual, in 1 Ethernet device. Unit, suited for data acquisition and reporting, collects data from CNC control with options for operator manual input. Data is presented via Management-Administration module with Real Time Status, Event Time Line, and Historical Analysis reports via MicrosoftÃ-® Excel on...

PC-Based System monitors and controls temperature/humidity.

Series LTM-8000 utilizes custom software to provide data acquisition, data logging options, and to web-enable any system for remote monitoring and control. Software permits connection of any PC to LTM-8000 Series data acquisition system controllers via RS-232 port. LTM-8000 provides 16 input points per channel, each of which provides both temperature and humidity monitoring for total of 32 data...

Handheld Module instantly transmits data to Pocket PCs(TM).

Handheld Wireless Information Module(TM) (WIM) provides real-time, remote access to statistics and maintenance data by communicating directly with main system controller via Open Process Control (OPC) interface to Microsoft Visual Studio.NET(TM) WebService(TM). OPC support enables unit to integrate with any existing OPC-compliant applications and uses WiFi 802.11b for radio frequency...

Trotec Laser Offers Customizable Industrial Laser Marking Solutions for Any Application

Trotec's laser marking solutions provide your company with configurable workstations and intuitive, customizable software. Check out our video to learn more.