New Connectors Products

Ground Fault Receptacles feature self-testing design.

CIRCUITPRO(TM) Devices continually test themselves every 60 sec to verify that they are fully operational, while still providing ground fault protection. Units quickly notify user if ground fault protection has been compromised or if ground fault condition exists. Status of ground fault is indicated through red and green LED on face of device. Available in commercial grade, hospital grade, and...

Wire Lead Receptacles suit hospital applications.

Pre-wired at factory, Hospital Grade Models 8200-L and 8300-L include three 6 in. No. 12 AWG THHN wire leads, locked-in wrap around strap, dual drive pins, die cast center bushing, and triple-wipe brass T contacts. Receptacle bodies and covers are impact-resistant thermoplastic and come in 7 faceplate colors. Available in 15 or 20 A straight blade models, with 2-pole, 3-wire grounding, units...

BNC Bulkhead Jack interconnects mother and daughter boards.

Separable circuit board jack, Trompeter 75 Ohm Model UCBJSE20F sends high-frequency signals directly from edge of PCB through motherboard into coax cable. Two-piece design consists of edge-mounted connector mounted to daughter board, and BNC body mounted over hole in motherboard. Edge mounted connector can be mated and de-mated through hole, allowing hot-swap interconnections without removing...

Modular Cable System comes in PVC or plenum versions.

Consisting of 2 Runners(TM) and selection of 8 BreakAway(TM) termination jumpers, RapidRun(TM) can handle UXGA, RGBHV, component, composite, and S-video along with left and right audio or S/PDIF digital audio signals in runs from 15-150 ft. Connector system allows Runner base cable to be pulled through Ã-¾ in. conduit with up to 90Ã-

Everything You Need to Know About E-Textiles

This ebook provides an in-depth overview into everything you need to know about E-Textiles.

Connectors offer VSWR performance up to 6 GHz.

Designed for use with Andrew CintaÃ-® cables, Connectors include N-Type, TNC, BNC, 7/16 DIN, UHF, Mini-UHF, and miniature units, as well as SMA, MCX, MMCX, SMB, SSMB, and MC Card models. Reverse polarity N-type, TNC, BNC, SMA, MMCX are available for Wi-Fi and Broadband applications. Offering crimp or clamp attachments, connectors are available with silver, gold, or nickel-plated components,...

Compression Connectors/Couplings have raintight design.

Raintight Compression connectors and couplings as well as PVC jacketed MC connectors and couplings are completely assembled, UL-listed, steel (Ã-½-2 in.) and zinc (Ã-½-4 in.) fittings. Connectors feature knockout gasket that prevents water seepage into box, while connectors and couplings utilize plastic sealing rings that protect water from entering conduit. PVC-jacketed MC cable...

Board-To-Board Connector targets portable electronics.

Designed with 0.4 mm pitch and 1.0 mm stacking height, Series 5805 employs twin-rib-shaped plug side contact that eliminates foreign obstacles from interfering with contacts. Fine lock mechanism with firm clicking response ensures secure termination. Connector allows users to check conductivity and short circuits under mated conditions. Since no metal is exposed on bottom of connector, Series...

Steel and Wood Stud Boxes align at right angle to stud.

Designed for use with Ã-½ or 5/8 in. wallboard, 22.5 in.Ã-³ Steel and Wood Stud Boxes accept eleven No. 14, ten No. 12, and nine No. 10 wires. Bracket countersink allows for No. 8 wafer head or dry wall screws with minimal wallboard bow. Classified for 2 hr wall and ceiling fire resistance, products have Height Site alignment guide and box levelers. Wood Stud Box offers hands-free...

Card Edge Connectors enable SHB Express(TM) backplane designs.

Vertical PCI Express(TM) Card-Edge Connectors support backplane designs based on System Host Board Express(TM) PCIe Specification. Connectors at interface between SHB and backplane are defined as x8 and x16 PCIe connectors. Backplane slots that interface with PCI Express peripherals can be supported with x1, x4, x8, or x16 PCIe connector links. Each serial PCIe lane is comprised of differential...

Coaxial System has miniature, single-row design.

With signal transmission up to 4 GHz, Mini Coax Single Row System features 3 contacts, 8 mm centerline distance, and 80 dB isolation. Right-angled modules are also available as pre-assembled, and both versions can be pressed in flat rock dies. Mini Coax connectors are suitable for equipment within cellular telecom infrastructure allowing for minimal slot distance of 15 mm.

Dies & Stamping Services with Over 25 Years of Experience

PDS is an established leader in progressive die stamping, with a reputation for providing precision and value that dates back more than half a century. Through extensive capabilities and a staff of seasoned professionals, we set the standard for quality, delivering flexible services that can meet the needs of the most challenging requirements. See our video to learn more.