New Applicators Products

Dispenser creates circular patterns and continuous beads.

Program-A-Swirl(R) maximizes adhesion between 2 substrates, using less material to wet-out greater area. Swirling is achieved when servo motor spins dispenser's nozzle. System can dispense single-component materials, or it can be used with static mixer nozzle for 2-component, reactive-resin materials. It is typically mounted at end-of-arm tool in robotic applications, or fixture-mounted in...

Glue Machine applies adhesive without runover.

Electric Top Side Edge Gluer applies adhesive to paper, card, corrugated stock, or binder board quickly and without runover. Machine glues any stock up to 1 in. thick and adjusts the glue film from 1/8 to 3 1/2 in. Adjusting glue film thickness is done by turning knob. It has fully enclosed gear motor, standard motor speed control, and large adhesive reservoir that holds more than 1 gal.

Print/Apply Systems have 64-bit microprocessor.

ALX 924/926 Print-and-Apply Systems offer maximum print speed of 16 ips. They produce 1D and 2D bar codes, graphics, and human-readable copy on range of label materials at 300 dpi print resolutions. The system's 1000-meter ribbon supply permits extended operation without ribbon changes. ALX 924 and 925 have print widths of 4.2 and 5 in., respectively. Both handle label widths up to 5.2 in. ALX...

Convertible Labeler offers versatility.

Convertible Labeler changes from label applicator to print and apply labeler in less than 15 minutes. Mini size accommodates 10 in. OD roll of labels and Standard size utilizes 16 in. rolls. Units include centralized keypad, screened label paths, and cantilevered printhead. Label sizes from .75 x .25 in. up to 4.1 x 14 in. can be applied.

Wire Harness: A Complete Guide

All you need to know about wire harnesses!

Can Tab Lubricator cuts oil use, reduces rejects.

MicroCoat(R) lubrication method gives can makers control over amount of oil applied to pull tabs. It lowers lubricant use and reduces residual oil that can migrate from tabs and lids into can contents. It has precision spray valves that use low volume, low pressure (LVLP) air to coat pull tab stock with fine film of oil that keeps dies sharp, eliminates pressroom mist and puddles, and minimizes...

Label Applicator does not dirty users' hands.

Fully programmable Tritone 100 label dispenser and applicator can be used in both vertical and horizontal positions. It applies labels with widths to 4 in. and lengths to 14 in. at rates of 1-30 meters/min. Stepper motor controlled Microprocessor control box provides LCD display for memory and change of label parameters. Tritone 100 works with conveyor speeds from 16 to 100 ft. per min.

Adhesive System eliminates mixing and metering.

Adhesive system incorporates PAM 500K, 500K Spray, and polyurethane cartridges. It uses compressed air to deliver adhesive at controlled and sustainable rate. Thermometer mounted on applicator allows observation of adhesive temperature. Normal operating temperature ranges are 90 to 325 deg F and 300 to 450 deg F. Common bonding substrates include wood, plastics, rubber, and plasticized vinyls.

Printer Applicator is RF enabled.

Model 5143 RF label printer applicator reads, writes, prints and applies RFID labels. Labels incorporate integrated transponder circuits that can be read, programmed and re-programmed using radio waves. Model 5143 RF can print and apply labels up to 5.04 in. wide from 16 in. dia roll at 203 dpi resolution. It utilizes Uniwall(TM) construction meaning that critical components are mounted onto...

Printer Applicator offers 5-page memory for setup parameters.

Model 3138 printer applicator includes 2-line digital display featuring full error messaging, keypad entry, and standard velocity compensation, which results in accurate label applications through changes in product velocity. Stainless steel and anodized aluminum construction is corrosion resistant providing durability in most hostile environments.

Lubrication System operates up to 4 valves.

MicroCoat uses low volume low pressure (LVLP) air to apply lubricant as fine film to reduce oil consumption by as much 70%. Compact, low-maintenance spray valves fit in tight press areas, and can be mounted in any position above or below stock. Valves coat every square in. of metal with fine, consistent film of oil, eliminating mist, dripping, or waste. System offers individual flow controls for...

Ensure Your Medical Device Meets Regulatory Standards with Triad's Custom Magnetics

Triad Magnetics' custom components for medical devices are designed and manufactured with the strictest regulatory standards in mind. Our capabilities include rapid design, prototyping, and testing of inductors, transformers, and power supplies for medical equipment. Check out our video to learn more.