ERICO International Corporation.

Rebar Splice requires no bar-end threading.
Electronic Components & Devices

Rebar Splice requires no bar-end threading.

Suited for new construction, repair, or retrofit applications, in-situ LENTON® LOCK coupler features gripping technology that provides for development of full rebar strength and structural integrity in tension, compression, stress-reversal, and dynamic applications. Coupler can be installed with standard wrench or impact wrench, depending on coupler size. Bolt heads shear off when proper...

Read More »
Ground Resistance Tester meets IEC 1010 standards.
Test & Measurement

Ground Resistance Tester meets IEC 1010 standards.

Measuring ground rod and small grid resistance in any season, handheld ERITECH® EST401 clamp-on tester can be used in multi-grounded systems without disconnecting ground under test. Probe enables measurement of current leakage flowing to ground or circulating in ground loops to 1 mA and neutral currents to 30 A(rms). With rugged Lexan® body, product is suited for taking measurements at service...

Read More »
Electrical Box Supports work with stud depths up to 4 in.
Architectural & Civil Engineering Products

Electrical Box Supports work with stud depths up to 4 in.

H23 Box Mounting Brackets attach 4 and 4 11/16 in. outlet boxes to wood or metal studs, accommodate 2-½ and 3-½ in. stud depths, and comply with NEC® Article 300.4(d) and CEC® Rule 12-3012. Extending stud depths to 4 in., CADDY MEB1 brackets mount on either side of stud without need to reposition box, and include V-notch on center for consistent positioning. Both electrical box supports...

Read More »
Conduit Supports securely attach conduit and cable to studs.
Material Handling & Storage

Conduit Supports securely attach conduit and cable to studs.

Screw-On Conduit Supports attach -½-1 in. EMT conduit or MC/AC cable to wood and metal studs. They comply with NEC® 358.30(A) and CEC-© rule 12-1404, which requires conduit support within 36 in. of electrical box. Units are gangable and work with both 1-½ and 2 1/8 in. deep boxes. Alignment tab positively locates fastener on stud, and serves to keep conduit in line with box knockout and...

Read More »
Distribution Blocks are IP 20 UL® finger safe.
Architectural & Civil Engineering Products

Distribution Blocks are IP 20 UL® finger safe.

Available with hinged/removable screw-retaining transparent covers that allow visual inspection of wire and confirmation of connection, single-pole ERIFLEX® distribution blocks have more than 95% fill ratio. Tinned copper blocks clip onto DIN Rail or mount to panels with screws. By keeping only one input, blocks can be supplied in parallel using jumper wire. They can be ganged for unlimited...

Read More »
Cable Retainer facilitates cable run direction changes.
Architectural & Civil Engineering Products

Cable Retainer facilitates cable run direction changes.

Installed vertically or horizontally on racks, ceilings, and walls, CADDY® CATCR50 plastic, low-voltage cable support is designed for use with CAT 5e and higher, fiberoptic, and coaxial cable. Rounded edges avoid over-bending and kinking of cables, and closure has locking teeth that retain bundled cable in one-piece support. UL®-recognized for air-handling spaces, product requires nail, screw,...

Read More »
Independent Support Clips accommodate tall T-grids.
Fasteners & Hardware

Independent Support Clips accommodate tall T-grids.

Designed to meet requirements of NEC® Article 410.16-C, CADDY® IDS series accommodate 1-½ and 1-¾ in. tall ceiling substructures (T-grids) in order to provide separate means of support for fixtures. Products have static load limit of 65 lb, and optional barrel nuts are available for low-profile track lighting. Packaged with all mounting hardware included, products do not require any tools for...

Read More »
Slotted Clevis Hanger helps reduce pipe hanging time.
Architectural & Civil Engineering Products

Slotted Clevis Hanger helps reduce pipe hanging time.

Available in 2 and 4 in. sizes, electro-zinc plated CADDY® SLOT LOCK is UL®-Listed and meets Factory Mutual deflection requirements without need for additional spacers. Removable slotted crossbeam accelerates assembly time and minimizes deflection by capturing top and bottom legs and locking them in place under load. Notches in crossbeam prevent it from working loose, even under extreme...

Read More »
Ground Rod Clamps are UL and CSA listed.
Electrical Equipment & Systems

Ground Rod Clamps are UL and CSA listed.

ERITECH CP58 and CP34 clamps connect conductors to ground rods or rebar to provide lightning protection and surge suppression. CP58 is UL and CSA Listed for -½ and 5/8 in. ground rods and #4 rebar, and is designed to accept #10 solid to #2 stranded conductor range. Listed for -½, 5/8, and -¾ in. ground rods, CP34 features conductor range of #10 to 1/0 wire. Both clamps are designed to...

Read More »
Pipe Clamps suspend vertical steel pipe risers.
Electrical Equipment & Systems

Pipe Clamps suspend vertical steel pipe risers.

CADDY® EZ RISER incorporates integrated serrated flange-head bolts that eliminate need to use wrenches on both bolt and nut during tightening, user can hold bolt in place with finger while tightening nut from front. Available for -½-12 in. steel pipes, clamps conform with Federal Specification WW-H-171 (Type 8) and Manufacturers Standardization Society SP-58 and SP-69 (Type 8). They come...

Read More »

All Topics