Rohde & Schwarz GmbH & Co
- DEU
Share:
Circuit Breakers are rated from .5 to 25 amps.
UL 489 is DIN rail mountable, only 13 mm wide, and designed to standard industrial control trip curves. Unit is used for branch circuit protection and comes in single and 2-pole version.
Read More »
Diode provides fast/soft recovery.
Stealth(TM) 1200 V diode is designed for switch mode power supply, motor drive, uninterruptible power supply, welding power, and induction heating applications. It combines fast/soft recovery switching with low reverse recovery current to reduce switching transistor turn-on losses in hard-switched applications. Diode is available in single and dual packaged configurations in TO-220 and TO-247...
Read More »
Garbage Cart holds 335 lb of waste.
Rotationally-molded BossKart(TM) has pleated panels in sidewall for vertical strength and to allow cart to recover quickly from squeeze of fully automated collection system. Extra deep latch bar pocket ensures secure hook up with lift systems. Cart has 12 in. molded HDPE wheels, 3/4 in. plated, solid steel axles, and molded-in scuff rails on base. Foot-tilt area allows easy access to axle for...
Read More »
Parallel Shaft Gearboxes have increased torque capacity.
Models SK 1282 through SK 5382 Clincher(TM) gearboxes have 41% more torque than company's previous models, yet have no gear ratio or dimensional changes. Therefore, engineering revisions by customer are not required to use increased capacity units. Gearboxes are available in 5 case sizes, all with 97% efficiency. Options include torque up to 28,320 lb-in.; power from 0.16 to 30 hp; output speeds...
Read More »
Digital to LVDT Converter has accuracy of -
Two-Channel 14-bit series accepts 14-bit offset binary or two's complement digital input, and converts it into two 0-7 V RMS outputs at 3 KHz. Output load is 2000 Ohms minimum. Other output voltages and frequencies are available. Part no. DLVDT314A-7-1 requires two's complement digital input, 7 V RMS reference input, and +5 V @ 1 ma, +15 V @ 25 ma, -15 V @ 25 ma maximum. Operating temperature...
Read More »CNCs suit common to complex applications.
PC-based Axium Power CNCs include wide range of digital drives and motors. ARS (Advanced Resonance Suppression) provides intelligent compensation for imperfections in stiffness and elasticity of machine by increasing feedback loop gain. Power panel runs under Windows(TM) 2000. Remote diagnostic, unattended CNC system back-up, or fully remote system operation is possible via Ethernet connection...
Read More »
SMB Connectors provide low mating and un-mating force.
SMB Series 75-Ohm Connectors include plugs, right-angle plugs, and PCB jacks for frequencies up to 4 GHz. RSB-301-179, positive-locking plug uses spring-loaded collar that must be retracted before connector will un-mate. RSB-300-1-179 straight and RSB-310-1-179 right angle crimp plugs feature standard snap-on coupling with gold plated contacts and body. RSB-350-1, vertical, and RSB-355-1, right...
Read More »
Laser Projection Equipment shows designs on work surface.
Z-Laser 2D, for woodworking applications, uses software to project full-scale data in red or green light directly onto bed of CNC machining center or assembly work area. By previewing cutting tool path, operator can ensure that blank is properly placed with correct grain orientation. This also eliminates possibility of damaging tooling or fixtures and permits proper pre-placement of part labels....
Read More »Dislodging Device duplicates blow of a sledgehammer.
Hopper Hammer automatically generates impact that dislodges dry material from sides of material handling equipment and unplugs hoppers, bins, and bunkers. It has greater acceleration than standard vibrators to overcome material's natural adhesive forces and cause fluid release of material pluggage or residue. Unit runs on 110 Vac and can operate in any position, making it suitable for chutes and...
Read More »
Digital Pressure Gauge has battery for field viewing.
Series SDPGB measures any media compatible with 316 stainless steel. It is available for applications from -30 in. Hg to 100 psig and 0 to 1000 psig. Digital readout provides real-time information when user pushes button. Automatic shutoff feature allows user to walk away after taking reading, thus conserving battery power. Zero and span calibration are possible when user has access to reliable...
Read More »