Aprima Medical Software, Inc
Carrollton, TX 75006
Share:
Marking System is computer-controlled.
Able to work as standalone marking system or integrate with other systems, MC-2000 Scriber produces alpha/numeric marks and logos on materials including metals, plastics, and ceramics. Character sizes from 1-20 mm are produced at speeds of 1-3 sec. Continuous contact of carbide stylus minimizes noise levels; diamond-tipped stylus is optional. Product has 3 x 2Ã-¼ in. marking window and is...
Read More »
Battery Pack powers portable CMMs.
Custom Nickel Metal Hydride battery provides 12 V output and includes short circuit protection for CMM arm. With life expectancy of 800-1000 charge-discharge cycles, unit powers CMM arm for 6-8 hrs under normal conditions. Product has one green and one red light that indicate level of charge. Red LED illuminates and stays lit once battery falls below minimum charge level. Physical dimensions are...
Read More »
Tap Aligning Center simplifies hand tapping.
Equipped with No. 2 Morse taper, Tap Aligning Center has spring center used to align taps when hand tapping in lathes or drilling machines. Suited for awkward tapping operations, product does not require user to constantly adjust center. Physical characteristics include hardened 5/16 in. dia center, 1 in. plunger travel, and overall length of approximately 5Ã-½ in.
Read More »
Epoxy Coating is suited for petrochemical facilities.
Fast CladÃ-® Edge Retentive Epoxy enables immersion service in 24 hr. Low odor, low-VOC, Bisphenol A amine coating offers greater than 70% edge build retention for corrosion resistance. When applied at 20.0 mils wet at 50% RH, the 98% solids tank lining is dry to touch in 1 hr and can be walked on within 4 hr. Designed for plural-component application equipment, product is suited for use over...
Read More »
Modular Automation Tooling is flexible for changing needs.
Tooling system allows users to construct vacuum end effector tools with minimal design time. Made of hard-coat anodized aluminum, system assembles on-site without welding or use of special tools. Tooling consists of swivel arm assembly with various functional attachments. Air-driven vacuum pump provides vacuum pressure through COAX(TM) technology and connection for blow-off pressure. Optional...
Read More »
Float Steam Trap simplifies installation and maintenance.
Universal-mount Model UFT14, with 2-bolt connection, incorporates FT14 Float Trap internals and offers all stainless steel construction and sealed design to resist leakage and corrosion. Internal air vent provides complete venting of air and non-condensable gases on start-up. Suited for saturated and superheated steam, unit provides condensate removal at steam temperatures, for maximum heat...
Read More »
Software Kit builds graphical interface for controller.
GUI Toolkit helps design and implement graphical interface on QVGA Controller to monitor and control instruments or industrial processes. Display screens and graphics objects are developed using any Windows paint program. GUI Toolkit can display system status using graphical representations, such as bar graphs or text-based messages. QVGA Controller mates embedded computer to 320 x 240 pixel EL...
Read More »
Speed Reducers offer increased torque ratings.
BrowningÃ-® Torque Taper Plus Shaft-Mount Reducer Models 307 and 315 are offered in ratios of 5, 9, 15, 25, and 35:1. Reverse mount bushing system allows user to mount bushing from either side. Barrier seal system combines V-ring face seal, grease-filled labyrinth, and rotating outer flinger to defend against contamination and oil seal damage. Units are suited for package handling, aggregate...
Read More »
Loop Back Module is suited for high-speed systems.
Suited for testing systems operating at 500 Mbps to 3.2 Gbps per channel, FCN-261Z00x matched-impedance loop-back module uses internal matched-impedance PCB to perform signal testing. Design offers crosstalk of less than 4% and in pair skew of less than 5 ps to maintain integrity of signal being tested. Unit has die-cast metal housing and latching mechanism. Overall, 12x device measures 48.9 x...
Read More »
Magnetic Proximity Sensors fit in tight spaces.
Series MP1014 Hall Effect Sensors provide solid-state sensing in 3.3 mm high package. Low-pressure injection molding process encapsulates sensors in polyamide for lower stress on electronics at temperature extremes. Standard termination is 12 in., 24 AWG PVC leads and distance between centerline of mounting holes is 16.5 mm. Sensors provide 3-wire sinking output and operate with supply voltages...
Read More »