Aprima Medical Software, Inc
Carrollton, TX 75006
Share:
CCFL Driver suits LCD backlighting applications.
Designed for use with Sharp 10.4 in. LQ104V1G21 LCD, Model LS530 DC-to-AC Inverter delivers 10 W of total output power. Measuring 5.1 x 0.8 x 0.5 in., dual-display unit features input range of 9.6-14.4 V and output current of 3.0-7.0 mA per lamp. Applications include gaming, marine electronics, medical, point-of-sale/kiosk, plus test and measurement equipment.
Read More »
Compression Molding Presses feature high-speed PLC.
Compression Molding Presses include multi-function software for real-time controls, alarms, and data logging. Upacting press, Model N, is suited for rubber and plastic, while Model M meets needs for heating or curing cycles. Fabri-Comp SMC and Thermoplastics Presses feature servo-controlled CNC with processing speeds to 100 ipm. RTM Presses suit closed mold process for polymer and fiber...
Read More »
Sealant Dispenser applies uniform beads without waste.
Ultra(TM) 870 Dispensing System connects to compressed air source and uses 0-100 psi pressure regulator to apply materials of different viscosities at steady, controlled rate. Fluid is contained in disposable syringe barrel connected to dispensing unit by flexible air line. Adjustable vacuum control prevents oozing between applications. Ultra(TM) 870 handles sealants, silicones, brazing pastes,...
Read More »PC Scope Adapter offers 1 Mb buffer memory.
USB-bus powered, PicoScope 3206 features 200 MHz analog bandwidth and single-shot, 8-bit sampling rate of 200 MS/s. Using Equivalent Time Sampling for repetitive signals, sampling rate is increased to 10 GS/s. Waveform storage is limited only by PC's storage capability. Once captured, PicoScope software allows user to zoom-in on signal at up to 2,000x magnification. Built-in signal generator can...
Read More »
Toroidal Inductors suit power applications.
Thru-hole Series 083AT features inductance from 10-100 Ã-µH and current ratings up to 30 Adc. High current/power capacity units are targeted for use in power supply filtering and energy storage applications. Specific applications include medical diagnostic, monitoring and analysis equipment, electrical/electronic test and measurement equipment, and commercial and industrial control systems.
Read More »Network Router utilizes 1.2 GHz Pentium III processor.
Teletrol Network Router, Model TNR, allows Teletrol Integrator facility controls systems to be directly connected to Ethernet and ARCNET enterprise-wide networks using IP or IPX protocols. Suited for building automation professionals, unit features internal 16 MB disk-on-chip hard drive and internal Ethernet port for 10/100 Mbps autonegotiate. Configuration files can be copied to and from TNR on...
Read More »PXI Module integrates PXI platforms in DAQ systems.
PXI Starter combines 3U, 8-slot chassis featuring 7 PXI peripheral slots and 400 W ATX power supply with PCI-PXI extension kit. Power supply, temperature, and cooling fans are monitored by built-in alarm in chassis. Warning LED and alarm are activated if failure is detected. PCI-PXI Extension Kits work as transparent PCI-PCI bridge register set and provide direct control of PXIS-2630 chassis from...
Read More »
Embedded Module features Intel i815E chipset.
Model ETX-P3T provides complete PC functionality in component that plugs into application-specific carrier board. Power management is achieved using ACPI and APM 1.2, allowing fanless cooling. Module supports Intel 82815 chipset with integrated Graphics Core, 2 IDE ports with support for ATA 33, 4 USB 2.0 ports, up to 512 Mbytes SDRAM, 10/100 Mbit Base-T Ethernet, LVDS up to SXGA 1,280 x 1,024,...
Read More »
Blind Hole Locking Clip manages cables in panels/chassis.
Model BHLWHC-500-01 locking clip has one-piece design that eliminates need for screws. Push fit installation is achieved with 6 mm hexagonal socket drive pressed on top of mounting fix, then pushed into a 7.9 mm dia blind hole. Barb end fix ensures secure fit, while releasable locking clip facilitates cable installation and removal. Available in Nylon 6/6 material, clip ensures that routed cables...
Read More »
Duburring Tools suit robotic and CNC applications.
Flexdeburr radially-compliant tools have floating air-turbine motor and spindle arrangement that provides deburring tip's radial compliance to perform consistently on irregular part patterns. Pneumatically controlled tools allow cutting bit to follow part profile, maintaining constant force on part surface. Pivot bearing provides radial movement. Tool requires clean, dry, non-lubricated air for...
Read More »