Aprima Medical Software, Inc
Carrollton, TX 75006
Share:
Pneumatic Level Sensors are for use in highly viscous liquids.
Manufactured with minimal moving parts, NLS sensors are suited for use in process industry applications where electrical power is not available or hazardous locations exist. Products install with Ã-½ in. pipe and G1 connection at top of tank, offering lifespan of more than 50,000 switch operations. Sensors may be used in conjunction with intrinsic safety barrier to meet hazardous location...
Read More »Machine Vision Camera has digital interface.
Equipped with power and trigger LEDs on rear panel, CV-M71 provides users with Ã-½ in. progressive scan, color camera based on Bayer CCD. It utilizes Sony ICX415AQ imager with 782 x 582, 8.3 Ã-µm square pixels. Capable of shutter speeds from 1/60-1/300,000 sec, camera operates at 60 fps at full resolution and 250 fps with 1/8 partial scan 24-bit RGB output via Camera Link base...
Read More »Pushbutton Switches are protected against contaminants.
Low-profile IA Series, offered with NO and NC/NO combined electrical functions, incorporates wire lead terminals and 16 mm bushing. Polyurethane membrane depresses when switch is actuated and provides IP67 front-of-panel seal to ensure resistance to frost, sand, and hydrocarbons. Available with 7 plunger colors, switches are rated 2 A max @ 24 Vdc resistive load, have electrical life of 1 million...
Read More »Spill Detection System works with syringe pumps.
Able to detect spills and leaks down to as little as 3 drops of liquid, OS 250 consists of moisture sensing mat, connection between mat and controller, and switched power outlet. When moisture is detected, system sounds audible alarm, flashes LED, and turns off power of any device plugged into single outlet, solid-state power controller. Reusable mats measure 30 x 30 cm and can be cut to any size.
Read More »Clear Polymer is suited for film applications.
Topas COC (cyclic olefin copolymer) enables blown film producers to make transparent films free of gels. Topas 8007F-400 clear cyclo-olefin copolymer adheres to polyolefins, can be metallized and colored, and has inherent moisture barrier. It also features 2,500 MPa modulus and 80Ã-
Read More »Transistors and Diodes are used in portable applications.
Digital transistors, bipolar transistors, small signal Schottkys, and small signal switching diodes are manufactured in SOT-723 flat-lead package, which measures 1.2 x 1.2 x 0.5 mm. Utilizing 1.44 mmÃ-² PCB area, discrete devices include 50 signal transistors and signal diodes suited for use in cell phones, PDAs, digital still cameras, and notebook computers.
Read More »DC-DC Converter suits 400 mA battery-operated electronics.
Monolithic, step-up, switching Model NCP1423 boosts voltage from 1 or 2 NiMH or NiCd cells up to usable level of 1.8 or 3.3 V. Synchronous rectification eliminates external Schottky diode, while Ring-Killer eliminates high-frequency ringing in discontinuous conduction mode. Switching frequency up to 600 kHz allows for low profile inductor and output capacitor to be used. Other features include...
Read More »PVD-Coated Inserts speed metal cutting.
Turning grades KC5010 and KC5025 are PVD-coated with Titanium Aluminum Nitride, which helps resist wear at cutting edge for machining of high-temperature alloys, stainless, and alloy steels. KC5010 uses 6% cobalt binder in substrate, offering deformation resistance for general-purpose and finish-turning applications. For more severe operations, KC5025 features 10% cobalt in base material to cope...
Read More »VAV Controller helps maintain tight flow accuracies.
TALON Predator Single Duct/Dual Duct Low Flow Controller is suited for flow ranges between 150-1,200 fpm, with tightest accuracy below 400 fpm. It provides quiet operation to eliminate occupant white noise. Variable air volume controller is suited for critical environments in hospitals, laboratories, industrial buildings, and medical offices where highly accurate building control is required.
Read More »Measurement Arm targets construction/home improvement fields.
Digital Template FaroArm captures measurement data electronically, enabling files to be e-mailed to shop and transmitted directly to cutting machine. System allows builders and fabricators to create files for countertops, backsplashes, side splashes, window sills, wall caps, breakfast counters, and other common shapes. It includes FARO Digital Template Measurement Arm and CAM2 Digital Template...
Read More »