Aprima Medical Software, Inc
Carrollton, TX 75006
Share:
Plane Bearings are suited for food and pharma processing.
Plane bearings, offered in straight and self-aligning configurations, are available as unmounted bearings and in pillow block assemblies in single, twin, and flange block types. TeflonÃ-®-lined bearings can be operated without lubrication, are resistant to chemicals, and have stainless steel body. Suited for vacuum applications, ceramic-coated bearings must be lubricated and withstand rapid...
Read More »
Color Proofing System eliminates manual draw downs.
Operating at up to 100 psi, automated, air-driven Sharper Color Proofer System(TM) enables printers to achieve less than 1 on delta E scale. It offers constant speed of 100 ipm and accepts up to 6 in. wide substrate. Constant speed allows for direct correlation of press, while push button operation allows for precision ink film thickness repeatability. System accommodates Echocel Junior(TM),...
Read More »Visualization Module suits press fitting applications.
Designed to analyze positional accuracy during assembly, Model DT85 allows user to view press fitting process results and measurement curves independently on up to 32 MP85 or MP85DP amplifiers by using CANbus. Measurement mode is used to gain global statistical information on complete process run. Parameter control mode allows transducer and amplifier parameters to be zeroed, checked, and...
Read More »Brush DC Servomotors achieve speeds to 5,400 rpm.
Available in 2 lengths, MAEÃ-® Series 500 can provide continuous torque up to 57 oz-in., depending on model. Units include 11-slot armatures to minimize magnetic cogging, ball bearings, and 2-pole stators. Speed, voltage, current, and torque characteristics can be tailored to meet exact application requirements. Motors are suited for data storage, medical/biotech, semiconductor processing,...
Read More »Modular Dock Bridge offers 15,000 lb capacity.
Designed to span gap between warehouse and trailer, LoadHog(TM) mounts to warehouse floor using 4 anchor bolts and requires no concrete work. Unit stores inside warehouse and allows dock door to close tight against floor. Arc design and raised side housings provide structural integrity that withstands 3- and 4-wheel forklift traffic. Available in 5, 6, and 7 ft widths, dock bridge features 17 in....
Read More »Electronic Controller targets OEMs and other integrators.
Featuring die-cast aluminum sealed housing with 210 x 240 mm footprint, Model A5:M2 maintains standard 70-pin connector with individually configurable input pins. Unit is suited for range of off-highway applications, including oil and gas equipment, agricultural equipment and implements, lift equipment, and material handling as well as selected on-road uses such as waste and recycling trucks, and...
Read More »
Wiring Duct controls cables in point-to-point wiring.
With 2-point contact design, Ty-Duct(TM) Wiring Duct is UL recognized for continuous use at temperatures ranging from -40 to 140Ã-
Read More »
Graphical LCD Display offers real-time data.
Featuring 6.5 in. VGA color LCD, Model D3:C4 presents information on parameters such as speed, flow, pressure, and temperature as well as diagnostic reporting and calibration functions. Information is obtained through data links that connect all electronic systems. Unit includes 4 NTSC/PAL video inputs, PIP video with 30 frames/sec, and internal audible alarm. Rated to IP69/NEMA 13, display is...
Read More »Work Area Vision System helps expand operator awareness.
Work Area Vision System provides operators with views from up to 3 cameras to improve operator awareness of surroundings, work tool activity, and changing work area conditions. Machine-mounted, closed-circuit camera system withstands vibration, pressure washing, and adverse environmental conditions. It comes with 7 in. color TFT LCD and cameras with panoramic (115Ã-
Read More »Aluminum Frames eliminate need for pressurizing.
Machine frames and workstations can be assembled using modular T-slotted aluminum extrusions that also act as manifold. Frames can be turned into manifold by capping off ends of extrusion with pressure manifold plates, which are made from clear anodized aluminum and can withstand up to 150 psi of positive or negative pressure. Pressure manifold plates can be side or end-mounted, and come complete...
Read More »