Tacton Systems
Stockholm 111 22 SWE
Share:
Gas Discharge Tubes protect sensitive telecom equipment.
Raychem Circuit Protection Gas Discharge Tubes (GDTs) protect telecom equipment from damage due to transient surge voltages that typically result from lightning strikes and equipment switching operations. Placed in front of and in parallel with equipment, they act as high-impedance component while not influencing signal in normal operation. In case of overvoltage surge, GDTs switch to...
Read More »
Servo Amplifier works with feedback from resolver sensors.
Able to drive brush and brushless motors to 7 hp, Xenus(TM) provides CANopen multi-axis motion control as well as stand-alone single axis motor drives. It reads feedback from resolver sensors to 14-bit accuracy at 10,000 rpm. Amplifier provides 15 kHz current loop update rate and 3 kHz position and velocity loop update rate. Built-in power supply enables amplifier to run on single or 3-phase...
Read More »
Switching Power Supply suits 1U-height medical applications.
Passive PFC-based, PAM150 provides universal 115/230 Vac input selection and single 150 W continuous power output. User may select one of several factory-set output voltages, including 3.3, 5, 12, 24, and 48 V. Unit meets appropriate Class A PFC and harmonic distortion requirements for medical equipment. It includes dc OK, ac power fail, and protection against overload, overvoltage, reverse...
Read More »
Ultrasonic Gas Flow Meter operates under high pressure.
FLOWSIC 600 measures actual volume flow rate, actual accumulated volume, gas velocity, or velocity of sound in gases. Available in standard sizes from 3-16 in., unit features 1-4 measuring paths, bi-directional measurement, and overload protection. Standard ANSI flange ratings are from 150-600 lb. Non-intrusive meter can be calibrated with ambient air, and is suited for flows with high dynamics...
Read More »
Brushless Motors utilize neodymium magnets.
Electronically commutated, Maxon EC-max Motors include Hall effect sensors, which provide feedback to control electronics. By assembling motor with coils outside rotor, heat dissipation and high overload capability is attained. Motors have stainless steel housing and vary in diameter from 16-40 mm with lengths from 24-88 mm. Continuous output power is 5-120 W, while maximum speed is 20,000 rpm....
Read More »PVDF Sheet Material suits semiconductor applications.
Polyvinylidene fluoride (PVDF), high-purity sheet material meets requirements of Factory Mutual (FM) Clean Room Materials Flammability Test Protocol, Class 4910. FM 4910, manufactured from KynarÃ-® 740 resin, features double-masked surface, fully traceable and verifiable resin, chemical-resistance, and UV-stability. It measures 4 x 8 ft with thicknesses from 1/8-1 in. Sheet features tolerance...
Read More »
Spectrometer is responsive from 200-1100 nm.
Model HR4000 has 3648-element CCD-array detector that enables optical resolution of 0.02 nm. It features dynamic range of 2.5 x 109 and signal-to-noise of 2500:1 for single integration period. Integrated onboard module has 10 user-programmable digital I/O lines, 13-bit analog input, 9-bit analog output, and pulse generator for triggering other devices. USB 2.0 interface enables full spectral...
Read More »
Voltage Regulator offers input capability down to 0.9 V.
Model LT3020 has low dropout voltage of 150 mV while delivering up to 100 mA of output current. Low VIN capability enables it to operate across voltage range of single-cell alkaline and NiMH batteries. Unit offers micropower operation with 120 Ã-µA of quiescent current and less than 3 Ã-µA in shutdown. Available in 8-lead DFN or MSOP package, regulator includes reverse-battery protection,...
Read More »
Linux Development Kit works with IXP425 XScale SBC.
Embedded Linux Development Kit is available for IXP425 XScale based network processor board, which includes two 100baseTx Ethernet ports, 4 USB 2.0 ports, 3 RS-232 ports, and one RS-422/485 port. Kit consists of ready-to-run embedded Linux system with full support for all on-board peripherals. It includes AC PSU, cables to connect to host system, and IXP425 based MERCURY PC/104 SBC fitted with 64...
Read More »
Die-Cast Aluminum Boxes feature external flanges.
NEMA 4X-rated, Series AN provides EMC protection and can be mounted on wall or panel without removing gasketed cover and exposing internal components. Permanently-fastened mounting bracket is 0.09 in. thick and accepts up to No. 10 mounting screws. Available in natural aluminum or black powder coat finish, boxes range in size from 1.95 x 1.77 x 1.12 in. up to 8.75 x 5.75 x 3.25 in. Cover mounting...
Read More »