Capital Safety Australia & New Zealand

Vertical Machining Center has Fanuc Motion Control System.
Communication Systems & Equipment

Vertical Machining Center has Fanuc Motion Control System.

Richmond 40 taper VMC 1000 weighs 10,000 lb, has cast-iron base, column, and saddle for dampening and rigidity, and uses dual supported, pre-tensioned 40 mm ballscrews that deliver repeatability of 0.0001 in. It has 1,181 in./min rate, 8000 rpm spindle, Fanuc control, and 15 hp spindle drive motor. Spindle has wrap-around coolant sleeve, grease-packed trucks and caged rollers for long life....

Read More »
Warehouse Management Software tracks stock, orders new.
Agricultural & Farming Products

Warehouse Management Software tracks stock, orders new.

Warehouse Rx(R) software provides real-time inventory control. It tracks items from receipt through storage, picking, and shipping, preventing lost inventory and out-of-stock conditions. Software directs replenishment of items when inventory drops below predetermined level. Cycle count processes ensure accurate inventory records, reducing or eliminating need for physical inventories. Counts can...

Read More »
Material Handling & Storage

Telescoping Crane mounts to standard rear axle truck.

Series 1400 has maximum lift of 33 tons and comes with choice of three booms: 100 ft four-section, 110 ft four-section, and 127 ft five-section with synchronous boom extension that distributes boom weight and maximizes reach by telescoping proportionally. Crane is road-legal without special permits, allowing it to go anywhere without special transport arrangements. Standard open-rail rider-seat...

Read More »
Tool Database fits ESPRIT CAM.
Software

Tool Database fits ESPRIT CAM.

WinTool Add-In from third party developer DATOS (Zurich, Switzerland) contains catalogues from leading cutting tool manufacturers. Now available for ESPRIT CAM software, it automatically transfers entire tool list and cutting tool parameters into ESPRIT system for use in creating tool path. For example, when setting up new tool with more than one dedicated cutting edge, WinTool provides crucial...

Read More »
Motor Drive ICs cool fan motors.
Controls & Controllers

Motor Drive ICs cool fan motors.

FAN8404D and FAN8408D are 2-phase, half wave motor drive ICs capable of sinking 1.2 A motor load current, while requiring 2.2 mA supply current in stand-by. FAN8408D features Hall output (HO) for motor speed detection and FAN8404D offers alarm output to signal fan lockup. Operating voltages range from 4 to 15 V. Units include built-in thermal shutdown (TSD) circuits, reverse-current protection...

Read More »
Material Handling & Storage

Telescoping Crane mounts on truck.

Series l400H behind-the-cab mounted crane has maximum capacity of 33 tons. Two booms are available: 100 ft, four-section boom with 30 ft pull-out jib, and 127 ft five-section boom with 30 ft single-section jib. Synchronous boom extension system distributes boom weight and telescopes proportionally. Crane mounts on standard commercial tandem rear axle truck and can be equipped with accessories,...

Read More »
Controls & Controllers

Digital Drives work with servo motors.

DR100EE Series can be used with brushed or brushless, rotary or linear servo motors. It has 20 kHz digital current loop that uses Space Vector Modulation (SVM) switching techniques that result in higher current loop bandwidth and lower heat dissipation. Drive configuration and tuning can be accomplished through graphical and intuitive Windows based utility using serial RS232/485 communication...

Read More »
Pressure Transducer comes in stainless steel body.

Pressure Transducer comes in stainless steel body.

Subminiature Smart Transducer Series offers choice of 1% or 0.1% FS accuracy. It has digitally programmed electronic circuit to provide zero offset, gain and temperature settings. Precision voltage regulator and buffer amplifier condition analog output signal. Transducer is sealed in stainless steel body with self-aligning snap-in 4 pin electrical connector.

Read More »
Software

Internet Portal provides browser access to IT functions.

B2E business-to-employee portal increases workflow, efficiency, and productivity by finding and delivering information relevant to user. Users have single point of interaction on company intranet, using normal Web browser. Portal handles interactions between IT environment and employees. It encompasses all systems within organization that are operated by employees, such as manufacturing systems,...

Read More »

All Topics