Table & Work Surface Isolators

Mounting & Attaching Products, Material Handling & Storage

Anti-Shock Components double as emergency food source.

April 2, 2015

Designed to reduce vibration and optimize equipment stability, Gell-Low Anti-Vibration Shock Mounts are created from recycled bovine by-products and produced in variety of sizes. Compression-mounted vibration isolators are also suitable for mounting under mobile cameras on drones and for isolating vibration in UAV applications. Available in red (strawberry), green (lime), and black (liquorice), products can also function as emergency food source for disaster conditions. Read More

Electrical Equipment & Systems, Electronic Components & Devices, Safety & Security Equipment, Mounting & Attaching Products

Non-Incendive Barrier Module isolates analog and discrete signals.

March 16, 2015

By providing electrical barrier between control devices and equipment installed in hazardous (Class 1, Division 2) environments, fuse-protected ASD-NIB Series minimizes risk of ignition on load side. This enables standard wiring practices to be used for in-field connections and eliminates need for explosionproof enclosures/conduit. At 6.2 mm wide, this non-incendive, CCSAUS-approved barrier module connects single-channel analog or discrete signal wires from 24–12 AWG. Read More

Material Handling & Storage, Laboratory and Research Supplies & Equipment, Mounting & Attaching Products

Shallow Glovebox conserves time and simplifies work processes.

June 20, 2014

With depth that fosters accessibility and removal of rear components, Easy-Reach USP-797 Compounding Aseptic Isolator (CAI) meets requirements for aseptic isolator and creates internal Class 100 (ISO 5) environment. Shallow design prevents need to move glovebox isolator away from wall in order to change filters or remove baffles for sterilization. Sliding door separates antechamber from main processing chamber, and each are monitored by independent pressure gauge.
Read More

Sensors, Monitors & Transducers, Mounting & Attaching Products

Vibration Sensor Isolators operate in hazardous areas.

September 10, 2012

Available in 1- and 2-channel versions, ISpac 9147 Series Ex i Isolators enable use of vibration sensors in hazardous areas. These sensors for condition monitoring of plants and machines allow users to detect any damages at early stage. Utilizing rotary switch for configuration, isolators are available as single units on DIN rail, with common power supply and collective error message via pac-Bus, or in pac carriers. Read More

Mounting & Attaching Products

Pneumatic Vibration Isolators suit loads up to 3,200 lb.

July 16, 2012

Based on Stabilizer(TM) hybrid-chamber design, I-800P Series delivers vertical and horizontal isolation. Units offer horizontal travel of 0.12 in. with repositioning accuracy of 0.003 in. Standard vertical releveling capability is ±0.010 in., but custom designs with releveling accuracy of 0.002 in. are available. Fitted onto 8 in.² leg weldments or manufactured on stand-alone legs, isolators have self-centering design that facilitates integration into OEM machinery and other process equipment. Read More

Mounting & Attaching Products

Bell-Shaped Rubber Mountings dampen shock and vibration.

February 29, 2012

Suited for static loads up to 1,956 lbf, V12Z55M062M Series is made from combination of natural rubber and styrene-butadiene rubber compound for pliability and elasticity. Of 12 isolators in series, 2 have 4-hole mounting and 10 have 2-hole mount configuration. All feature welded steel plated nut at top of housing. With durometer hardness ranges of 45 and 60 ±5, mountings are suitable for use under controllers, large pumps, fans, motors, compressors, and other medium load equipment. Read More

Material Handling & Storage, Mounting & Attaching Products

Insulating Grommets dampen vibration as well as noise.

February 14, 2012

Anti-Vibration Grommets are engineered for electrical insulation, mechanical damping, and noise suppression in office or lab equipment. Specifically, products are engineered to isolate sensitive instrumentation from unpredictable vibration and shock. Integrated fingers flex as needed to provide necessary dampening, while shoulder screws provide correct spacing for full tightening. Able to accommodate .031-.125 in. thick panels, grommets are manufactured from EPDM rubber in black or blue. Read More

Material Handling & Storage, Mounting & Attaching Products

Optical Table Isolator uses negative-stiffness technology.

May 27, 2011

Offered with up to 4 x 8 ft table and gross load capacities to 2,000 lb, MK52 optical table isolation support system may be used where external vibrations adversely affect operation of sensitive equipment. Horizontal isolation is provided by beam columns connected in series with vertical-motion isolator. When adjusted to ½ Hz natural frequency, system achieves 93% isolation efficiency at 2 Hz, 99% at 5 Hz, and 99.7% at 10 Hz. Tables are constructed with plated-steel honeycomb core. Read More

Material Handling & Storage, Mounting & Attaching Products

Cylindrical Vibration Isolation Mounts come in metric sizes.

April 28, 2011

Suited for elastic mounting of machine units such as motors, compressors, and pumps, RoHS-compliant series GN 351 features natural rubber body, vulcanized, with 55 durometer (±5° shore hardness). Variations include those with 2 tapped holes, 1 tapped hole and 1 threaded stud, or 2 threaded studs. Steel cover plate is zinc plated, blue passivated, and molded in, as are tapped inserts or threaded studs. Sizes and dimensions allow use in diverse applications requiring vibration isolation. Read More

Material Handling & Storage, Mounting & Attaching Products

Vibration Isolation Baseplate minimizes microscope disturbance.

April 4, 2011

Without requiring any air lines, compressors, or other accessories, VIBe(TM) reduces vibrations that can disturb sensitive instruments and microscopes. Table-top platform comes in 2 rectangular and 2 triangular shapes to satisfy application requirements. It features black powder-coated steel plate and mechanical isolators that provide vertical and horizontal vibration isolation. IB isolator bearings are available in discrete payload ranges from 10-100 lb. Read More

HVAC, Mounting & Attaching Products

HVAC Isolator supports rooftop HVAC installations.

February 1, 2011

Using patented Seicon System®, Seicon HVAC Isolator reduces vibrations emitted from rooftop HVAC installations by more than 85%. Wind-resistant isolator minimizes living area noise and is designed for use with structurally mounted residential HVAC condensers. Unit can be attached to most surfaces and will isolate any HVAC condenser up to 400 lb when used as pair. It can also be used on heavier condensers in greater numbers. Read More

Mounting & Attaching Products

Wire Rope Isolators suit military and industrial applications.

October 5, 2010

Protected against multiaxial shock and vibration, V10Z70 Series includes 70 versions that offer corrosion-resistant, maintenance-free operation. Cable is made from stainless steel, mounting plates are of aluminum, and there are 10 available cable diameters from 1/16-7/8 in. In addition to military and aerospace applications, areas of use include electronic racks, shipboard electronics and equipment, rotating equipment, as well as on and off road transport. Read More

Mounting & Attaching Products

Circular Wire Rope Isolators feature low profile design.

August 9, 2010

Suited for compact military and industrial applications, corrosion resistant V10Z69 series of 18 circular wire rope isolators feature multi-axial shock and vibration protection. Incorporated cable is made from stainless steel, while mounting plates are made of aluminum. Available in 1/16, 3/32, 1/8, 3/16, and ¼ in. dia cable, mounts are suited for applications including computers, electronics, medical equipment, generators, motors, and pumps. Read More

Mounting & Attaching Products

Wire Rope Isolators suit heavy-duty applications.

March 26, 2010

Comprised of 70 wire rope isolators, V10Z70 Series feature multiaxial shock and vibration protection, corrosion-resistance, and maintenance-free operation. Mounting plates are made of aluminum, and cables are made of stainless steel and stocked in 1/16, 3/32, 1/8, 5/32, 3/16, ¼, 3/8, ½, 5/8, and 7/8 in. dia. Uses include military applications, electronic racks, shipboard electronics and equipment, rotating equipment, aerospace, and on/off road transport. Read More

Electrical Equipment & Systems, Mounting & Attaching Products

USB Isolator provides security through galvanic separation.

April 24, 2009

EN 60601-1 and EN 60601-1-2 certified and approved, USB-interface isolator USB-GT protects USB against surges of up to 4,000 V using optocouplers. It is powered either by USB-interface or optional external power supply. EN 60601-1-2 certification allows connection of non-medical peripheral devices such as printers via USB-GT MED to medical devices such as x-ray, ultrasound, endoscope, or laser systems. Read More

Electrical Equipment & Systems, Electronic Components & Devices, Mounting & Attaching Products

Isolator Mounting Bases isolate sensors up to 1,500 V.

July 23, 2008

Measuring 1 in. across flats with 0.82 mounting pad, Models SF21 and SF22 accommodate up to medium diameter accelerometers and small diameter side-exit accelerometers. Models SF23 and SF24 are both 1 1/8 in. across flats with 0.94 in. mounting pad that can accommodate large diameter top-exit sensors. All have ¼-28 integral stud on accelerometer side, and are used to prevent voltage spikes from reaching sensor by electrically isolating it from case of machine. Read More

Computer Hardware & Peripherals, Mounting & Attaching Products

Ethernet Isolators safely connect process field devices.

November 26, 2007

Combining intrinsically safe energy limitation and galvanic isolation, FieldConnex® Ethernet Isolators enable high-speed data devices located in hazardous locations to be connected directly to standard Ethernet line. Products also allow for back-to-back, pass through applications without requiring any separate hardware. PCB-mounted version allows OEM to seamlessly integrate intrinsically safe Ethernet into their own equipment. Read More

Electrical Equipment & Systems, Electronic Components & Devices, Mounting & Attaching Products

Voltage Isolators offer 1, 25, and 150 Mbps speed options.

July 31, 2007

Supporting any combination of 3.3 or 5 V supplies, ISO722x family digital isolators feature 1 nsec channel-to-channel skew, 3 nsec part-to-part skew, 1 nsec jitter, 1 nsec pulse width distortion, and 4 kV ESD protection. Integrating capacitive isolation technology, units provide immunity against data corruption due to 25 kV/µs voltage transients. Facilitating PCB layout, Model ISO7220 has 2 channels in same direction, while Model ISO7221 has 2 channels in opposite directions. Read More

Electrical Equipment & Systems, Electronic Components & Devices, Mounting & Attaching Products

Intrinsic Safety Isolators are 12.5 mm wide.

June 25, 2007

HiC family of Intrinsic Safety Isolators provide single channel of isolated power and ultra-thin housing for reliable industrial signal transmission and system availability. Motherboard-mounted HiC modules feature SIL 2/3 rating and 0.8 W power dissipation that keeps cabinets cool. Units can be fastened onto 8 or 16 slot termination boards without need for tools or wiring, and can be expanded with HART communication board and fault indication board. Read More

Mounting & Attaching Products

Electrical Box Extender/Insulator corrects setbacks.

March 20, 2007

Models BXE-100/200/300 feature continuous, smooth, nonmetallic side walls that completely enclose devices, creating insulating barrier between them and their respective metal boxes. Extender does not interfere with wiring, so no trimming is required. Mounted completely flush with wall, products fit most metallic or nonmetallic electrical boxes and accommodate GFCIs. While BXE-100 and BXE-200 correct up to 1 in. setbacks, BXE-300 corrects up to 5/8 in. setbacks. Read More