Phoenix Contact
Harrisburg, PA 17111 0100
Feb 22, 2008 Able to monitor different time functions without using complicated controllers, Electronic Timer Relays can be adjusted to array of timing settings ranging from milliseconds through several days. Colored LEDs report operating status as well as limit value and relay state. ETD devices equipped with special functions, including star/delta or Wye/Delta and watchdog are also available.

Picker Components Inc.
Carrollton, TX 75006
Feb 21, 2008 Available in top flange, side flange, and plain case mounting configurations, Model PC740 includes silver alloy contacts and heavy swinger wires that go down to contacts to carry current load and minimize heat in springs. Two-pole version is rated 40 A, 250 Vac, while 3-pole version is rated 30 A, 250 Vac. Measuring 55.2 x 52.0 x 38 mm plus mounting tabs, relay is suited for driving motors and actuators, battery chargers, heater elements, industrial controls, and safety circuits.

Macromatic Controls, LLC
Menomonee Falls, WI 53051
Feb 21, 2008 Comprised of intrinsically safe control switch input and electromechanical relay output, ISP Series provides safe method to control load with input device located in hazardous area. Products are incapable of releasing sufficient energy to cause accidental ignition of hazardous material by minimizing current level on input side of unit. When control switch in hazardous area is closed, relay is energized. When control switch is opened, relay is de-energized.

Phoenix Contact
Harrisburg, PA 17111 0100
Feb 13, 2008 Designed for applications requiring nominal current rating up to 10 A, PLC-RELAY high-current terminal block relays with plug-in SPDT contacts connect to 6 and 14 mm PLC-RELAYS using press fit bridge. Featuring a patented plug-in bridging system which eliminates daisy chain wiring and reduces installation time. Reverse polarity and kick-back diode are included to protect relay and controls. Product is available with either screw or spring terminals.

Dwyer Instruments, Inc.
Michigan City, IN 46361 0373
Feb 08, 2008 Used to monitor shaft seal of pumps before failure, Series DLD dual-channel leak detection relay finds leaks by sensing status of float or conductivity switch installed in seal cavity. It offers NO relay contacts to energize alarm and deenergize pump in event of leak and includes LED indicator. Installed via 2-pin octal mount, unit is available in sensitivities of 10-25 kW adjustable and 4.7-100 kW adjustable. All models utilize 120 Vac control voltage.

CIT Relay & Switch: Division of Circuit Interruption Technology, Inc.
Maple Grove, MN 55369
Feb 05, 2008 Automotive A5 Series relays feature contact resistance of less than 50 mW initially, insulation resistance of 100 MW at 500 Vdc, and maximum switching power of 360 W with maximum switching voltage of 75 Vdc, 380 Vac. Dielectric strength is 750 Vrms minimum at sea level and contact-to-contact is 500 Vrms. Operating from -40 to +85°C, sealed, immersion-cleanable relays are available in coil voltage options of 6, 9, 12, 18, and 24 Vdc with coil power choices of 1.6 and 1.9 W.

Omron Electronics LLC
Schaumburg, IL 60173
Jan 23, 2008 Measuring 19.6 x 15.6 x 15.6 mm, Model G5LA offers switching capacity of 10 A at 250 Vac/24 Vdc and 5 A at 250 Vac/24 Vdc on NO and NC contacts, respectively. With CTI of greater than or equal to 250, it conforms to VDE0435, UL508, and CSA 22.2 standards. Model G5LA-CF comes with Class F coil insulation and UL/CSA approved ambient operating temperature range of -40 to +85°C. Nominal coil power consumption is 360 mW for 5, 9, 12, and 24 Vdc coils and 480 mW for 48 Vdc coil.

Phoenix Contact
Harrisburg, PA 17111 0100
Jan 14, 2008 Certified according to DIN EN 50155 VDE 0115 Part 200 railroad standard, 6 or 14 mm pluggable PLC RW relay modules operate over ambient temperature range of -40 to + 70°C, and have vibration and shock features. With 1 or 2 changeover contacts, coupling relay modules come equipped with spring cage connectors and can switch loads up to 250 Vac/10 A. Wear-free solid state relays in accordance with EN 50155 for loads up to 110 Vdc/3 A are also available.

Comus International
Clifton, NJ 07012
Jan 10, 2008 Providing high insulation resistance of 1,014 W, MDAS Series mercury-free, dry reed relays come with internal electrostatic shield. Relays are specifically designed for ATE markets, measurement equipment, and test and control systems.

CIT Relay & Switch: Division of Circuit Interruption Technology, Inc.
Maple Grove, MN 55369
Dec 18, 2007 Resistant to shock and vibration, J115F3 Series is available with contact arrangements of SPST NO, SPST NC, or SPDT. It incorporates 40 A contacts, 240 Vac, 30 A @ 277 Vac, and Class F insulation. Offered in panel mount style QC for both coil and contacts, series offers dielectric strength coil to contact of 2,500 Vrms and coil voltage choices from 3-110 Vdc and 12-277 Vac. Options include standard 0.9 W or 0.6 W coil and compliance for UL873 and UL508 spacing requirements.

STMicroelectronics
GENEVA   Switzerland
Dec 04, 2007 Produced in PowerSSO24 package, VNI4140K quad high-side solid-state relay utilizes VIPower(TM) technology in order to minimize on-resistance. Solution integrates logic interface, drivers, and protection circuits on same chip as power stage. IN addition to per-channel diagnostic bits and double thermal protection, IC offers over-temperature, short-circuit, and over-current protection as well as under-voltage shutdown, demagnetization, and protection against loss of ground.

Pickering Interfaces
Wobum, MA 01801
Dec 03, 2007 Available in 2-, 4, and 8-slot BRICs, 40-563 PXI switch matrix features solid-state switches that have continuous current rating of 0.25 A and can sustain inrush currents of 0.75 A for 100 ms. Switches ensure rise and fall times of typ 20 ms without contact bounce, and each switch has typical on resistance of 0.8 W, providing typ path resistance under 2.5 W between X axis connections. Model 40-563 is available in matrix sizes from 64x8-384x8.

CIT Relay & Switch: Division of Circuit Interruption Technology, Inc.
Maple Grove, MN 55369
Nov 27, 2007 Measuring 29.0 x 12.6 x 15.7 mm, fully sealed J114FL Series is available with SPST NO, SPDT, DPST NO, and DPDT contact arrangements with contact ratings of 16 A at 250 Vac/30 Vdc and 8 A at 250 Vac/30 Vdc. Unit has max switching power of 480 W, 4,000 Va; max switching voltage of 440 Vac, 125 Vdc; and switching current of 16 A. Equipped with cadmium-free contacts, RoHS-compliant relay features 400 mW coil power consumption and F class insulation.

CIT Relay & Switch: Division of Circuit Interruption Technology, Inc.
Maple Grove, MN 55369
Nov 20, 2007 Incorporating immersion cleanable and flux tight construction, J114AF Series is available with SPST and DPDT contact arrangements with contact ratings to 16 A at 250 Vac, 30 Vdc. Units feature max switching power of 480 W, 4,000 Va; max switching voltage of 380 Vac, 110 Vdc; and switching current of 16 A. Equipped with cadmium-free contacts, RoHS-compliant relays are suited for power supplies, lighting control, motor control, thermostats, modems, and test equipment.

Omron Electronics LLC
Schaumburg, IL 60173
Nov 09, 2007 Providing up to 40 A switching capacity per pole on NO contact, Model G7Z features resistive load rating of 40 A at 440 Vac for NO contact and 25 A at 440 Vac for NC contact. Space saving unit is offered in 12 or 24 Vdc coils, and maintains dielectric withstand of 4,000 Vac between coil and contacts. Suited for inverter, solar/fuel battery, and Uninterruptible Power Supply applications, it has inductive load rating of 22 A at 440 Vac on NO contact.

Schneider Electric
Palatine, IL 60067-7399
Nov 09, 2007 Capable of switching up to 15 A dc and 10 A ac and built with heat sinking capability in 17.5 mm modular design, Magnecraft 861 eliminates need for heat dissipation calculations. RoHS-compliant unit features 100% solid state operation, integrated snubber, and isolated input and output circuits. Finger-safe terminals protect operators from live currents and accidental shocks. Suited for medical equipment and lighting, relay mounts to DIN rails as well as panels using extendable tabs.

CIT Relay & Switch: Division of Circuit Interruption Technology, Inc.
Maple Grove, MN 55369
Nov 06, 2007 Measuring 20.2 x 5.3 x 12.8 mm for high-density mounting, J112 Series Sub-Miniature Relay carries 0.12 W rating and offers SPST NO contact arrangements. Two pin layout configurations are available: J112 offers 5.08 mm spacing between terminal pin-out of switch function, and J112K offers 7.62 mm spacing. Available with 5 A contact rating @ 250 Vac resistive or 30 Vdc resistive, shock- and vibration-resistant product features 6 coil voltage options from 5-24 Vdc.

CIT Relay & Switch: Division of Circuit Interruption Technology, Inc.
Maple Grove, MN 55369
Oct 26, 2007 Available with SPST NO, SPST NC, or SPDT contact arrangements, J115 Series is offered in 3 versions: PC termination, combination PC and QC for contacts, and panel mount style QC for coil and contacts. Series exceeds UL standards, incorporating 40 A contacts, 240 Vac, 30 A @ 277 Vac, and Class F insulation. Exhibiting shock and vibration resistance, relays are immersion cleanable with cover and available with coil voltage choices from 3-110 Vdc (12-277 Vac).

Electroswitch, Unit Of Electro Switch Corp.
Weymouth, MA 02188 2913
Oct 24, 2007 Series 24 SCSR facilitates remote control and monitoring of circuit breakers while retaining local control through manual trip/close handle. As addressable network device with certified DNP 3.0, product provides remote trip-coil monitoring (single or dual), sequence-of-events reporting, system battery monitoring, and self-diagnostic reporting. Units are configurable with up to 6 decks, each containing 2 isolated contacts enclosed in molded phenolic insulators.

Schneider Electric
Palatine, IL 60067-7399
Oct 15, 2007 Featuring modular design with plug-and-play DIN rail mount options, Square D® SEPAM Line includes Series 80 for critical sources and loads, Series 40 for important sources and loads, and Series 20 for basic source and load requirements. Units feature graphical software package for programming, and backlit LCD display that allows multi-line text plus graphics. Display lets users view multiple metered values, as well as alarm and diagnostic functions.