Vibration Damping Mounts

DIN Rail Mounted Monitor protects smaller plants, equipment.
Vibration Damping Mounts

DIN Rail Mounted Monitor protects smaller plants, equipment.

Able to monitorÂ- 2 channels of bearing vibration, shaft vibration, or shaft position, Ethernet-enabled DN26 G3 offers fully programmable signal conditioning with range of measurement algorithms and sensor options. Dedicated speed monitor channel can also be utilized as phase reference for harmonic analysis of vibration signals, and sensor interface is programmable to accept...

Read More »
Shock Absorption Mounts come in body diameters from 1-2 in.
Vibration Damping Mounts

Shock Absorption Mounts come in body diameters from 1-2 in.

Available in inch sizes, GN 452.1 (threaded stud) and 452.2 (tapped hole) cylindrical vibration/shock absorption mounts with stainless steel components are used as end-stop bumpers. RoHS-compliant products, also known as vibration isolation mounts, anti-vibration mounts, vibration bobbins, and rubber bumpers, absorb most accumulated kinetic energy upon impact. While dampening and preventing...

Read More »
AirLoc 700 Series Damping Pads Used Successfully in Large Municipal Water District Engine/Pump System
Vibration Damping Mounts

AirLoc 700 Series Damping Pads Used Successfully in Large Municipal Water District Engine/Pump System

AirLoc engineering was contacted to make a recommendation for vibration isolation on a large municipal water district engine/pump system in Sothern California. The 9,000 lb. system was supported on a 3/4 inch steel plate using 6 mounting feet. After initially testing a soft" pad configuration with too much defection, 715 damping pads and iso-washers were evaluated with a bolt-through...

Read More »
Moldtech Inc.'s Custom Application Improves Isolator Protection
Vibration Damping Mounts

Moldtech Inc.'s Custom Application Improves Isolator Protection

Lancaster, NY – Moldtech Inc. was asked to manufacture an isolator that would stand up to continual drenching in diesel-fuel-based cutting fluid and would not experience any degradation in isolation performance or fatigue life. The traditional isolator manufacturing process bonds natural rubber to metal mounting plates; natural rubber provides optimum isolation ability and excellent fatigue...

Read More »
Seal Stuff In, Seal Stuff Out
Sponsored

Seal Stuff In, Seal Stuff Out

One of the best ways to make sure that your machinery stays up and running in the face of adversity is to make sure that it's properly sealed. Of course, it's not always easy to determine whether the integrity of your seals are up to par. How can you tell when you have a problem?

Read More »
Vibration Damping Mounts

Shock & Impact Information from Kellett's Unique 3 Layer LP13 Vibration Isolator Pad Leads Way to Stronger Battlefield Armor

KELLETT Ent., Inc. is poised on the edge of discovery, and will soon acquire new information on the shock & impact response of the unique 3 layer LP13 Vibration Isolator Pad. As the supplier of material to a research project at the Watervliet Federal Arsenal in Albany, New York, we have been extended the opportunity to place piezo accelerometers within the impact pit. The impact pit is found...

Read More »
Vibration Damping Mounts

Parallel Mount Kit connects motor to ball screw actuator.

Available in 4 standard frame sizes from 3–6 in., Parallel Mount Kit enables virtually any motor to be connected in parallel to any linear ball screw actuator, regardless of manufacturer. PMK has max output torques from 2.4–46 Nm in 1:1 pulley transmission ratio. Cover plate is machined from aircraft aluminum and anodized for further protection. Featuring conical taper bushings for optimal...

Read More »
LP-13 Developed to Reduce HVAC Vibration
Vibration Damping Mounts

LP-13 Developed to Reduce HVAC Vibration

The LP-13 Shake Absorber® Vibration Isolation pad, developed by Kellett Enterprises, Inc., has a 3 layer design to reduce vibration and noise under machinery including commercial and residential HVAC units. The vibration is isolated when you place a composite material between the source of vibrationÂ- - your equipment - and the support structure for that equipment. Vibration in one...

Read More »
Dual Stiffness Isolation Mount suits moving load applications.
Vibration Damping Mounts

Dual Stiffness Isolation Mount suits moving load applications.

Offering alternative to active vibration isolation systems, Vibralevel DSM provides both active damping and vibration isolation. Unit eliminates platform tilt by activating stiff mode when load undergoes aggressive move.Â- On signal from machine controller, mount transitions from softer vibration isolation system to stiffer support platform within 500 ms. When move is complete,...

Read More »
Triangle Manufacturing Partners with Robur for High-Efficiency HVAC Solutions
Vibration Damping Mounts

Triangle Manufacturing Partners with Robur for High-Efficiency HVAC Solutions

Triangle is proud to partner with Robur to increase efficiency in the HVAC industry; helping both the environment and consumers. Triangle Manufacturing is proud to partner with Robur, who offers one of the most advanced solutions in HVAC, using up to 40% of renewable energy. Robur, a German manufacturer of heat pump heating and cooling systems and Triangle, a Wisconsin-based manufacturer of motor...

Read More »
Shaft Mounts offer design flexibility.
Vibration Damping Mounts

Shaft Mounts offer design flexibility.

Manufactured from weldable 1117 steel and stocked in Â-¼–2 in. ID sizes, Shaft Mounts offer many design options, including short- and long-length collar sections with set-screw or single and multiple clamp-screw configurations, and mounting flanges in various shapes and hole patterns. Units can also be supplied with and without keyways. For added flexibility, mounts can be manufactured in...

Read More »
Cut and Bevel Pipe up to 63" Diameter with a Single Lightweight, Portable Machine
Sponsored

Cut and Bevel Pipe up to 63" Diameter with a Single Lightweight, Portable Machine

CS Unitec is a leader in power tools designed for industrial applications, with products that set the standard for robust performance and industry-leading reliability. Adding to our long list of innovation is a new line of pipe cutting machines. For cutting and beveling pipe up to 2" in thickness and diameters from 12" to 63", no other cutting system comes close. See our video to learn more.

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers