Force Sensors / Transducers

Force Sensors / Transducers

Test System utilizes steering effort sensor.

Offering torque capacities of 200, 500, or 1,000 in-lb, Test Measurement System combines portable data acquisition system with air-bag compatible, Model 01184 digital FM telemetry steering effort sensor that transmits and receives torque signal. Providing 7,200 ppr, encoder directly attaches to windshield and is driven with gear drive chain. System also includes laptop computer and measurement...

Read More »
Force Sensors / Transducers

Rivet Monitoring System removes risks of blind riveting.

Integrating into assembly process, SmartSet(TM) System provides instant installation feedback that does not rely on operator skill or attention. Micro-strain sensor takes readings during rivet setting cycle to record variables such as riveting failures and use of incorrect rivet types within application. In RUN mode, system monitors each sequential rivet set and compares results with learned...

Read More »
Force Sensors / Transducers

Torque Transducers suit aerospace hydraulic pumps/motors.

Rotating torque transducers utilize non-contact, rotary transformers for sending excitation voltage to, and receiving measurement signals from, strain gage instrumented rotating sensor element. Flange and splined shaft design conforms to AND 10262 and 20002. In addition to torque output signal, optional pickup provides output proportional to speed and optional K type thermal couple to monitor...

Read More »
Force Sensors / Transducers

Load Cell facilitates brake testing.

Designed with 3 in. diameter flat loading surface, Brake Pedal Load Cell measures force where direction of load changes. Set of tapped holes on underside and mounting bracket allow it to be firmly attached to pedal. Load cell gives same output, ±1%, no matter where force is applied across surface. By minimizing error due to off-axis loads, unit is suitable as part of portable system for...

Read More »
Screwdriver Spindle features inline torque sensor.
Force Sensors / Transducers

Screwdriver Spindle features inline torque sensor.

SIZE-1 Screwdriver Spindle includes torque transducer based on strain-gauge technology, which obtains torque values by measuring reaction torque of gearing. Transducer connection is integrated with guide bolt above drivers' mounting area, providing access and protecting against damage. Minimum torque for spindle is 0.34 lb-in. and precision level of transducer is less than 1% standard deviation.

Read More »
In-Line Rotary Torque Sensors offer 16-bit resolution.
Force Sensors / Transducers

In-Line Rotary Torque Sensors offer 16-bit resolution.

Suited for automotive powertrain dynamometers, TORKDISC® Series 5300 features on-board electronic module that converts torque signals into high-speed digital representation. Digital data is transmitted to non-contacting pick-up loop with no risk of noise or data corruption. Remote receiver converts digital data to analog output voltage, frequency output, and serial digital output. Units...

Read More »
Small-Capacity Sensors measure torque down to 5 lb-in.
Force Sensors / Transducers

Small-Capacity Sensors measure torque down to 5 lb-in.

Flange-mounted Series 2308, 2309, and 2508 strain-gage reaction torque sensors are supplied with shunt calibration resistor and are NIST traceable. Featuring 2 mV/V output sensitivity, products are available in capacities from 5-1,000 lb-in. FS for measuring torque in applications such as lubricant studies, torsion testing, bearing friction, small motor dynamometers, stepping switch torque, and...

Read More »
Force Sensors / Transducers

Transducer resists lateral forces.

Suited for synchronous force and displacement measurements, U3 force transducer resists lateral forces and bending moments caused by weight of any connected machine parts that can lead to measurement errors. Lateral forces up to 100% of nominal rated force can be absorbed by welding supporting membrane parallel to measuring element through outer ring. Compact product, available in 8 measuring...

Read More »
Foot Plates aid in rehabilitation of foot and leg.
Force Sensors / Transducers

Foot Plates aid in rehabilitation of foot and leg.

Instrumentation grade Type 9281 and 9287B force plates incorporate piezoelectric force sensors with quartz crystals that convert force into data signal. Designed into foot tracks that don't reveal instrumentation beneath, patient steps, walks, or runs as instructed on outlined zone. Graduated force patterns visually represent physical condition, and impressions are captured for gait in motion...

Read More »

All Topics

COVID-19 Response Suppliers COVID-19 Response:
Can Your Company Help Provide Critical Supplies?

We are using the power of our platform to aid in the mass shortage of critical supplies. If your company can help provide supplies, capabilities, or materials for products such as N-95 Masks and Tyvek SuitsPlease let us know.

COVID-19 Response Suppliers