EMC Filters are designed for PV inverters up to 1,500 A.
Installed between inverter and solar panel, FEDC series ensures compliance with EMC standards for entire PV system by reducing conducted emissions towards solar panel and EMI radiations from solar panel. Product is available with ratings from 25-1,500 Adc, without terminals up to 150 Adc, and with screw connections up to 1,500 Adc. While meeting EN60939, UL1283, and RoHS requirements, series has...
Read More »
Feedthru Filters address automotive EMI concerns.
Featuring miniature surface mount design, LC T configured FeedThru Filters provide design engineers with consistent broadband EMI filtering for critical drive by wire applications such as throttle and braking. AEC Q200-qualified units typically provide -30 dB of attenuation across 300 MHz frequency spectrum. Response can start as low as 75 MHz or end as high as 1,500 MHz. Current ratings range...
Read More »
IPADT IC combines common-mode filtering and ESD protection.
Model ECMF02 single-channel IC and ECMF04 two data-channel unit combine common-mode filtering, which prevents data errors caused by EMI, and ESD protection needed by high-speed data lines. Measuring 0.55 mm high, Integrated Passive and Active Device (IPADT) products feature 6 GHz differential bandwidth, and common-mode attenuation of -34 dB at 900 MHz and -20 dB between 800 MHz and 2.2 GHz. They...
Read More »
DC Blocks pass frequencies from 300 kHz to 3 GHz.
Suited for use in broadband coupling and test and measurement applications, CBLK DC Blocks are designed to block DC voltage while passing frequencies from 300 kHz to 3 GHz. Units produce flat frequency response and offer low insertion loss of 0.02 dB at 300 KHz and 0.20 db at 3 GHz. DC input voltage is rated at 16 WVdc max and operating temperature range is -55 to +90-
Read More »
Metal Finishing Selection Guide
This unique chart compares different metal finishes by cost, corrosion resistance, applications and more.
Read More »
Low-Dissipation EMI Filters are military and aerospace rated.
Model FGDS-2A-50V is rated from 4-50 W at up to 2 A input current and measures 35.5 x 20.5 x 10.7 mm, while FGDS-10A-50V, rated from 50-150 W at up to 10 A input current, is housed in 40.8 x 27 x 12.7 mm package. Measuring 40.8 x 27 x 16.5 mm, model FGDS-20A-50V is rated from 150-300 W at up to 20 A input. All modules withstand transient and spike requirements of MIL-STD-704A and MIL-STD-1275B,...
Read More »EMI Filter provides inductance and series resistance.
Featuring miniature case size of .156 in. OD x .128 in. ID with body length of .200 in. and overall length of .715 in., L Circuit EMI Filter is suited for microwave and RF applications. Hermetically sealed, feed-through solder-in unit provides filtering from 10 kHz to 10 GHz, with 10 pF to 0.033 -µF capacitance, 10 A current rating, and voltage ratings from 50-200 Vdc. Monolithic capacitor...
Read More »EMI Filter Plates Now Available with 1500 VDC Flash Protection
Fairview, PA - October 19, 2010 - Spectrum Advanced Specialty Products has developed the capability to add 1500 VDC Flash protection to its complete line of EMI Filter plates, ideal for any application where higher voltage surge protection is required. Adding flash protection to any of Spectrum's Bolt-in, EasyMate® or Shrouded Latch filter plates enables them to withstand up to 1500 VDC flash,...
Read More »Texas Instruments Delivers Thinnest EMI Filters with Highest ESD Performance
DALLAS - Texas Instruments Incorporated (TI) (NYSE: TXN) today introduced six- and four-channel electromagnetic interference (EMI) filters for LCD display applications, the TPD6F202 and TPD4F202. Electrostatic discharge (ESD) ratings exceed the IEC 61000-4-2 specification by at least three times for contact discharge. Both are 67 percent better than the specification for air-gap discharge. This...
Read More »Weatherproof Low-Pass RF Filter suits CATV applications.
Model CX5060 filter passes cable television (CATV) Docsis 3.0 signals, blocks multimedia-over-coax signals, and provides RFI shielding and surge protection within weatherproof metal housing. Unit's pass band frequency is from 5-1,002 MHz with impedance of 75 W and provides over 40 dB of insertion loss in 1,125-2,300 MHz frequency range. Operating over temperatures of -40 to +85-
Read More »Two-Stage EMI Filters suit one-phase systems.
Characterized by high symmetrical and asymmetrical attenuation, FMBB NEO Series includes Design C, which attenuates potentially strong conducted interferences; Design D, which handles high frequency interferences; and Design F for low frequency attenuation. Units are dimensioned as 250 Vac filters with rated current of 1-36 A according to IEC and 125/240 Vac, 1-30 A according to UL/CSA....
Read More »
Trotec Laser Offers Customizable Industrial Laser Marking Solutions for Any Application
Trotec's laser marking solutions provide your company with configurable workstations and intuitive, customizable software. Check out our video to learn more.
Read More »
