Common Mode Filter suppresses EMI on DisplayPort interfaces.
Measuring 1.25 x 1.0 x 0.6 mm, TCM1210U-500-2P wide-band thin-film common mode filter suppresses noise on DisplayPort connections for signal transmission between computers or audiovisual equipment and display monitors. DisplayPort link uses up to 4 lines, each rated for 2.7 Gbit/sec, resulting in total transfer rate of 10.8 Gbit/sec. Unit features 8.0 GHz cutoff frequency, 50 W common mode...
Read More »DC Front End Module comes in 2.28 x 2.2 x 0.5 in. package.
Providing EMI filtering and transient protection, M-FIAM9 28 V front-end module meets conducted emission/susceptibility per MIL-STD-461E and input transients per MIL-STD-704A/E/F and MIL-STD-1275A/B/D. With input voltage of 10-36 Vdc and output power up to 500 W, ruggedized unit can be mounted onboard or inboard for height-critical applications. It comes in 2 environmental grades, including -55...
Read More »DC Front End Module comes in 2.28 x 2.2 x 0.5 in. package.
Providing EMI filtering and transient protection, M-FIAM9 28 V front-end module meets conducted emission/susceptibility per MIL-STD-461E and input transients per MIL-STD-704A/E/F and MIL-STD-1275A/B/D. With input voltage of 10-36 Vdc and output power up to 500 W, ruggedized unit can be mounted onboard or inboard for height-critical applications. It comes in 2 environmental grades, including -55...
Read More »
EMI Filter Adapters come with 9, 15, 25, or 37 pins.
Available in 4 standard filter values from 47-3,900 pF, male and female D-Sub filter adapters provide electronic noise reduction in applications ranging from high-speed digital broadcasting to industrial test equipment. They are suited for both EMI corrections in existing applications or for filter tests during design phase. Adapters complement D-Sub filter SMC connectors as retrofit solution for...
Read More »
In-Mold Electronics
To learn more about in-hold electronics (IMEs) and solutions offered by Eastprint, Inc., download now.
Read More »
EMI Filter Adapters come with 9, 15, 25, or 37 pins.
Available in 4 standard filter values from 47-3,900 pF, male and female D-Sub filter adapters provide electronic noise reduction in applications ranging from high-speed digital broadcasting to industrial test equipment. They are suited for both EMI corrections in existing applications or for filter tests during design phase. Adapters complement D-Sub filter SMC connectors as retrofit solution for...
Read More »
Audio IC combines handset audio filtering and ESD protection.
From 2.42 x 1.92 x 0.65 mm flip-chip package, EMIF06-AUD01F2 implements complete EMI filtering and ESD protection for stereo headset output and external/internal microphones. Audible handset demodulation noise is eliminated by achieving -25 dB attenuation throughout stop-band 800-2,480 MHz using high-density 1.3 nF PZT capacitors on microphone lines. ESD protection is achieved via combination...
Read More »
Audio IC combines handset audio filtering and ESD protection.
From 2.42 x 1.92 x 0.65 mm flip-chip package, EMIF06-AUD01F2 implements complete EMI filtering and ESD protection for stereo headset output and external/internal microphones. Audible handset demodulation noise is eliminated by achieving -25 dB attenuation throughout stop-band 800-2,480 MHz using high-density 1.3 nF PZT capacitors on microphone lines. ESD protection is achieved via combination...
Read More »Filter Architecture boosts mobile handset signal integrity.
Based on coupled inductor design, Praetorian-® III LC filter architecture utilizes 6-pole pi-filter topology and enables design of filters that can fit into small form factor, 0.4 mm pitch uDFN and chip scale packages. Filters, optimized for inductance and capacitance (down to 10 pF), promote attenuation and signal integrity. Products based on this architecture address EMI filter and ESD...
Read More »Filter Architecture boosts mobile handset signal integrity.
Based on coupled inductor design, PraetorianÃ-® III LC filter architecture utilizes 6-pole pi-filter topology and enables design of filters that can fit into small form factor, 0.4 mm pitch uDFN and chip scale packages. Filters, optimized for inductance and capacitance (down to 10 pF), promote attenuation and signal integrity. Products based on this architecture address EMI filter and ESD...
Read More »Electronic RF Filters are designed for shielded enclosures.
Mounted through outer wall of shielded enclosure, Series FCP power line penetration filters are RFI-secure and supplied with threaded nipple. Products are supplied with bleeder resistors to prevent shock hazards and can withstand 140% of rated current for 15 min without any deterioration. Providing specified insertion loss of 100 db min over indicated frequency range, series filters from 60-400...
Read More »
SEALTITE® Fittings and Cord Grips Offer Longer Lasting Protection
Anamet Electrical's 316 Stainless steel SEALTITE® fittings and UL-listed cord grips protect sensitive wiring components from fluids, corrosive contaminations, bumps, and abrasions with a steel core and liquid tight conduit jacket. Check out this video to learn more.
Read More »
