EMI / RFI Filters

EMI / RFI Filters

EMI Filter has 15-100 V range.

Suited for wide range of applications such as automotive, avionics, telecom, and ground systems, Model PFL4000 EMI filter is designed to meet filter requirements of conducted emissions per MIL-STD-461E for 5-100 W dc/dc converters. It features 99.5% efficiency, MTBF of 47.6 million hr, 6-sided shielding, and thermally conductive epoxy packaged in 1 x 2 x .5 in. metal case.

Read More »
EMI / RFI Filters

Common Mode Filter suppresses EMI on DisplayPort interfaces.

Measuring 1.25 x 1.0 x 0.6 mm, TCM1210U-500-2P wide-band thin-film common mode filter suppresses noise on DisplayPort connections for signal transmission between computers or audiovisual equipment and display monitors. DisplayPort link uses up to 4 lines, each rated for 2.7 Gbit/sec, resulting in total transfer rate of 10.8 Gbit/sec. Unit features 8.0 GHz cutoff frequency, 50 W common mode...

Read More »
EMI / RFI Filters

DC Front End Module comes in 2.28 x 2.2 x 0.5 in. package.

Providing EMI filtering and transient protection, M-FIAM9 28 V front-end module meets conducted emission/susceptibility per MIL-STD-461E and input transients per MIL-STD-704A/E/F and MIL-STD-1275A/B/D. With input voltage of 10-36 Vdc and output power up to 500 W, ruggedized unit can be mounted onboard or inboard for height-critical applications. It comes in 2 environmental grades, including -55...

Read More »
EMI Filter Adapters come with 9, 15, 25, or 37 pins.
EMI / RFI Filters

EMI Filter Adapters come with 9, 15, 25, or 37 pins.

Available in 4 standard filter values from 47-3,900 pF, male and female D-Sub filter adapters provide electronic noise reduction in applications ranging from high-speed digital broadcasting to industrial test equipment. They are suited for both EMI corrections in existing applications or for filter tests during design phase. Adapters complement D-Sub filter SMC connectors as retrofit solution for...

Read More »
Audio IC combines handset audio filtering and ESD protection.
EMI / RFI Filters

Audio IC combines handset audio filtering and ESD protection.

From 2.42 x 1.92 x 0.65 mm flip-chip package, EMIF06-AUD01F2 implements complete EMI filtering and ESD protection for stereo headset output and external/internal microphones. Audible handset demodulation noise is eliminated by achieving -25 dB attenuation throughout stop-band 800-2,480 MHz using high-density 1.3 nF PZT capacitors on microphone lines. ESD protection is achieved via combination...

Read More »
EMI / RFI Filters

Filter Architecture boosts mobile handset signal integrity.

Based on coupled inductor design, Praetorian® III LC filter architecture utilizes 6-pole pi-filter topology and enables design of filters that can fit into small form factor, 0.4 mm pitch uDFN and chip scale packages. Filters, optimized for inductance and capacitance (down to 10 pF), promote attenuation and signal integrity. Products based on this architecture address EMI filter and ESD...

Read More »
EMI / RFI Filters

Electronic RF Filters are designed for shielded enclosures.

Mounted through outer wall of shielded enclosure, Series FCP power line penetration filters are RFI-secure and supplied with threaded nipple. Products are supplied with bleeder resistors to prevent shock hazards and can withstand 140% of rated current for 15 min without any deterioration. Providing specified insertion loss of 100 db min over indicated frequency range, series filters from 60-400...

Read More »
EMI / RFI Filters

EMI/RFI Filters meet MIL-F-15733 specification.

Dual and triple circuit power line electronic filters run at operating temperatures from -550 to +850°C; voltage ratings are 115 Vac, 400 Vdc, O-400 Hz. With minimum insertion loss characteristics, MIL-F-15733/75 filters suit variety of noise and interference filter and safety requirements of electro-magnetic compatibility. Also available is single circuit power line filter IAW to...

Read More »
EMI / RFI Filters

Inlet Filters feature earth line choke.

Model FN9233E IEC inlet filter includes earth line choke that helps reduce interference signals on ground wire. They are designed for maximum continuous operating voltage of 250 Vac, 50/60 Hz and frequency range of DC to 400 Hz. Also featuring current rating of 1-15 A at 50°C maximum as well as operating temperature range of -25 to +85°C, devices have MTBF of 1,710,000 hr at...

Read More »
Precision Machined Parts for High Tech Applications
Sponsored

Precision Machined Parts for High Tech Applications

For precision and value that sets the standard for quality and craftsmanship, EGS Production Machining is the source for precision and value. Our extensive capabilities and dedication to customer service allow us to deliver the optimal manufacturing solution. See our video to learn more.

Read More »

All Topics