Three-Phase Ground Fault Display promotes corrective action.
Model GFD detects and indicates phase of first ground fault condition on ungrounded or isolated system, enabling corrective action to avoid potential hazards resulting from second ground fault. Flashing red LED gives positive fault indication of phase-to-ground fault or lost connection to corresponding phase. Supplied in 94V-0, flame-retardant, black ABS plastic, panel-mount enclosure, unit has...
Read More »Emerson's Smart Wireless Network Monitors Eye Wash and Safety Shower Stations to Improve Safety at Boise Inc. Paper Mill
Automated monitoring delivers real-time data to plant operators with 60 percent installed cost savings compared to wired technology AUSTIN, TEXAS (October 21, 2008) - Boise Inc. has enhanced safety response capability at its paper mill in St. Helens, Oregon, by implementing Smart Wireless products from Emerson Process Management to monitor its eye wash and safety shower stations. When one of the...
Read More »Module processes vehicle network sensor data.
Solo Matrix(TM) signal acquisition and translation module aggregates up to 32 analog or digital signals and converts them into vehicle network messages. It has 2 differential current measurement inputs, 2 variable reluctance and Hall-effect inputs, and 22 single-ended 12-bit analog inputs with ESD-protected, 28 V full scale signal conditioning. Unit is rated from -40 to +125-
Read More »
Transducers measure -90 to +90 phase differences.
Designed to sense phase angle difference between ac current and voltage signals, CR6300 Series includes 3 models with 0-5 Vdc, 0-10 Vdc, or 4-20 mAdc output. Units are powered by single 24 Vdc power supply, and have window openings to accommodate current carrying wires up to .26 in. diameters. They offer up to 500 V input voltage and up to 25 A of current. Housed in 3.26 x 1.42 x 2.99 in....
Read More »
An Operations Manager's Guide To The Mobile Connected Factory of Tomorrow
This white paper provides an overview of mobile technology for managing your manufacturing facility, while also discussing the advantages of being an early adopter.
Read More »Low-Power SMT RMS Detector accurately measures RF power.
Supplied in 3 x 2 mm DFN, LT5581 broadband 10 MHz to 6 GHz RMS detector features 40 dB dynamic range and 1.4 mA operating supply current. DC voltage output, proportional to log input power, provides mV/dB scaling with linearity exceeding -
Read More »
Wireless Monitoring System helps monitor remote plant assets.
Allowing operators to monitor inaccessible plant equipment, Essential Insight(TM) .mesh Wireless Condition Monitoring Solution enables temperature and vibration data to be transmitted wirelessly from asset to system software platform. With wireless sensors, system also helps enhance worker safety and ability to monitor equipment in hazardous areas. System comprises of wSIM(TM) sensor, Essential...
Read More »Patented Non-Contact SAW Torque Transducers Available in Custom Ranges
Pittsford, NY: TorqSense RWT320 is a series of digital, configurable, non-contact SAW rotary torque transducers with integral electronics and serial output. Available in versions from 500mNm to 10,000Nm, RWT320 interfaces with LabView-based software to indicate on any PC or laptop the torque, speed, power, and peak torque of rotating drive systems, ideal for monitoring, testing, or control....
Read More »
Assessment Kit fosters vibration energy harvesting adoption.
Wireless sensor node assessment kit, wSNAK, confirms advantages of condition monitoring systems powered by vibration energy-harvesting. Its 4 energy harvester-powered wireless sensor nodes send vibration/temperature data to laptop-based receiver, and each sensor node runs IEPE accelerometer with integrated temperature sensor on flying lead. Data is sent from each node, via IEE802.15.4...
Read More »
In-line Sensor monitors electrostatic charge build-up.
Model 875 features measurement probe with automatic calibration technology that maintains accuracy and speed even as distance between non-contacting probe and monitored surface changes. Features include measurement range of -
Read More »Transponder offers drivers toll collection feedback.
Compatible with all MARK IV electronic toll collection readers deployed in US, Canada, and Mexico, driver feedback transponder alerts users to successful toll payments and warns of low account balances. Tag is based on G4E active transponder technology that delivers 99.99% capture rates.
Read More »
SRG Global Coatings Enhance Surface Durability, Efficiency, Design Flexibility
SRG Global's automotive coatings enhance the structural integrity of the finished part while also improving vehicle efficiency. Check out our video to learn more.
Read More »
