Electrical Connectors

Keyless Shaft Connections lock parts in position.
Electrical Connectors

Keyless Shaft Connections lock parts in position.

ETP shaft connections slide onto shaft and provide solid keyless connection between shaft and hub to position and lock pulleys, sprockets, and gears. They eliminate need for keyways, tapers, and tapped holes, which can cause component stress and wear. Connections have double walled steel sleeve filled with pressure medium that expands when compressed by screw tightening mechanism. They are...

Read More »
RAST Connector suits appliance/white goods applications.
Electrical Connectors

RAST Connector suits appliance/white goods applications.

Double IDC (insulation displacement contact) ECO-DOMO double termination connector enables termination of two conductors at one connection point. Its 5 mm spacing may be used for double- or single-wire connections. Rated 10 A, 250 V for wire sizes 18 to 20 AWG, it enables the joining of several components over one connection point. Double flat spring contacts offer clean IDC connections that...

Read More »
Fixed Terminal Block provides top-mount access.
Electrical Connectors

Fixed Terminal Block provides top-mount access.

Suitable for power supply connections, 8486 Top Series is designed in 2-, 3-, and 4-pole versions with 7.62 mm pitch spacing. Top-mount wire entry permits wiring the block where access is limited. It provides screwdriver and wiring access on same plane to maximize PC board space. Series is UL rated for 300 V, 30 A for stranded and solid wire, sizes 22 to 10 AWG (VDE rated for 36 A). Each block is...

Read More »
Stereo Jacks come in two and three positions.
Electrical Connectors

Stereo Jacks come in two and three positions.

Models CTP-JD-3502 and CTP-JT-3503 are 2- and 3-high 3.5 mm stereo jacks, respectively. They have PC99 colors for proper identification for PC industry. RFI/EMI shield helps protect interference from transmitting from unit to outside world. It also protects system from picking up interference on cables. Plastic is UL 94-V0 for safety, and contacts are gold plated for low resistance to plug. Jacks...

Read More »
Connectors/Cable Assemblies suit telecommunications hardware.
Electrical Connectors

Connectors/Cable Assemblies suit telecommunications hardware.

RFH Series Connectors are low profile MHF coaxial connectors with mounting area of 3 mm x 3 mm on PCB and 2 mm height when mated. Cable assemblies test frequency rating VSWR of 1.3 max up to 6 GHz. MHF connectors have nominal impedance of 50 ohms with dielectric withstanding voltage of 150 Vac rms and temperature range of -40 to +90°C. RFH-4910-1 right angle plug and RFH-4911 PCB mount MHF...

Read More »
Rectangular Connectors fit CONTACT® EPIC® housings.
Electrical Connectors

Rectangular Connectors fit CONTACT® EPIC® housings.

UL, CSA, and VDE approved, EPIC® HEE Series high density connectors have 16 A, 600 V rating. Family consists of 6 contact capacity configurations: 10, 18, 32, 46, 64 (2x32), and 92 (2x46). Crimp terminated inserts are available with silver or gold contacts. Connectors are suitable for robotic, transportation, automotive, and industrial applications.

Read More »
Bus Bar Contact connects and disconnects quickly.
Electrical Connectors

Bus Bar Contact connects and disconnects quickly.

For use with PowerPole® 180 and SB®175 housings, 180 A bus bar contact attaches directly to copper bus allowing quick connect/disconnect of cables. Quick disconnect minimizes system assembly, replacement, or repair time. Contacts are made from solid copper, are silver plated, and are threaded to provide simple attachment to bus without need for special tooling. Bus bar contacts...

Read More »
Snap-In AC Inlet is rated 20 A/250 V.
Electrical Connectors

Snap-In AC Inlet is rated 20 A/250 V.

Model 4793 is offered in several versions to suit panel thicknesses from 1 to 3 mm, with 6.3 mm quick-fit terminals or solder tabs. Body is made from UL94-V0 thermoplastic, and contact pins and terminals are bright electro-tin plated brass for low resistance. Inlet is designed to comply with EN 60320-1/C20 for Class I cold condition. It is approved at cURus 250 V/20 A and VDE 250 V/16 A.

Read More »

All Topics