Fiber-Optic Connectors facilitate cable termination.
Singlemode AMP NETCONNECT LightCrimp Plus connectors allow for precision alignment of cabled fiber to factory-polished, stubbed ferrule. To terminate fiber, installer strips fiber, cleaves fiber, and crimps connector. Connectors exceed TIA/EIA 568 B.3 and ISO/IEC 11801 Insertion Loss and Return Loss specifications and are suited for direct termination applications and backbone or horizontal...
Read More »
Modular Coaxial Connectors offer 2, 3, or 4 ports.
CoSMID 75 ohm, surface mountable connectors incorporate plastic housing that can be plated and molded into various configurations. They feature 1.0/2.3 coaxial interface to CECC 22230 with typical reflection factor of less than 0.1 up to 500 MHz. Units can be processed through normal reflow soldering processes at temperatures up to 473Ã-
Read More »
Card Edge Connectors accommodate 0.062 in. daughtercards.
Right-angle, high-density, double-row Card Edge Connectors feature 1 mm centerline spacing with more than 50 signals per linear inch. Units have selective gold plating and hairpin bellow contacts. They offer signal contact current rating of 1 A and daughtercard engagement force of 1.5 N per contact. Devices are provided in contact configurations from 2/4 to 50/100 in single increments, and may be...
Read More »BNC Connectors maximize space utilization.
Series 6700/01BNC within-series adapters permit parallel routing of cables, either horizontally or vertically. Series 6717/18/19 coaxial connectors with adapters allow mounting of 2 BNC connectors in same PCB space. Both types are rated at 500 V with 5,000 mW insulation resistance, 50 W impedance, and 0-4 GHz frequency. BNC within-series adapters meet common BNC/F connector-interface...
Read More »
Guide To Swageless Fittings
Electroline specializes in innovative, easy-to-install swageless fittings. The following guide will highlight everything you need to know about swageless fittings.
Read More »BNC Connectors are designed for minimum return loss.
High-performance broadcast/HDTV-quality connector models 6702/03/04/05 are designed to meet broadcast standards with reduced return loss for signal clarity. Made with gold-plated brass center contacts, they offer true 75 ohm impedance and are accurately matched to Belden cables. Connectors are precision machined from brass and offer black nickel plating and high-density PTFE insulator material...
Read More »
Port Connectors suit 37-
ADACONN(TM) Port Connectors, when used with ADAFLANGE(TM) adapters and/or ADAFLANGEPORT(TM) adapters, give flexibility in plumbing compact SAE Four Bolt Flange connected systems without welding. Fluid is confined to inner bore where supporting wall thickness is greatest. Connectors are proof tested with Code 62 ADAFLANGE(TM) and ADAFLANGEPORT(TM) adapters to proof pressure of 18,000 psi and are...
Read More »
RF Coaxial Connectors have center contacts.
Suited for military and commercial applications, LC Series connectors feature female with closed-slot center contact and male version with rounded center pin. They are available as straight thru or right angle plugs and female receptacles, and as between series adapters. Rated for 50 ohm impedance, DC to 1 GHz, and 5,000 V, they are constructed with brass body, beryllium-copper female contact,...
Read More »
Fiber Optic Connectors and Adapters are self-sealing.
Series ST-DRY(TM) HP and FC-DRY(TM) HP connectors, adapters, and permanent bulkhead feedthroughs are 300 Series SS, while ST-DRY(TM) and FC-DRY(TM) connectors and adapters are nickel-plated brass. Corrosion-resistant products are environmentally sealed to protect fiber optic terminations from liquids, gases, and particulate that can interfere with transmission. Permanent bulkhead feedthroughs...
Read More »
I/O Module connects pushbuttons to Devicenet(TM).
With IP67-rated, built-in DeviceNet eurofastÃ-® connector, FDN20 DeviceNet station fits into any standard pushbutton enclosure. Screw terminals are accessible from inside enclosure, and unit powers I/O from DeviceNet. Model FDN20-4S-4XSG-E has 4 dedicated inputs and 4 inputs or outputs and can handle following I/O mixes: 8 in, 7 in/1 out, 6 in/2 out, 5 in/3 out, or 4 in/4 out.
Read More »
BNC Connectors suit serial digital applications.
Terminated using industry-standard crimping tools, NE8000 Series connectors have knurled body design and contact captivation to insure proper contact placement. Brass-bodied connectors are nickel-plated, have gold-plated contacts, and Teflon insulation. Characteristics include 75 ohm impedance, 5,000 megohm insulation resistance, and return loss from -25 db to 2 GHz. Contact retention is 6 lb...
Read More »
Precision Machining Solutions with Over 25 Years of Experience
Quality, customer service, and unbeatable value are the hallmarks of Hogge Precision. Since 1989 we have built a reputation as the go-to precision machining source, servicing many demanding industries. For CNC machining and screw machining, there are few manufacturers that can match our capabilities and expertise. See our video to learn more.
Read More »
